Search
Now showing items 1-10 of 61
ASTM G174: Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact
Abstract: This test method covers ranking rigid engineering materials for abrasion resistance in rubbing against aluminum oxide abrasive finishing tape. Though most solids can be tested, this test method addresses its use for metals, and coatings applied to metals.
The values stated in SI units are to be regarded as standard. No other units of measuremen...
The values stated in SI units are to be regarded as standard. No other units of measuremen...
ASTM F362/F362M: Standard Test Method for Determining the Erasability of Inked Ribbons
Abstract: This test method covers the determination of the erasability of inked ribbons.
Results are expressed in visual ranking order or in comparison to a control.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system ...
Results are expressed in visual ranking order or in comparison to a control.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system ...
ACI 210R: Erosion of Concrete in Hydraulic Structures
Abstract: INTRODUCTION
Erosion is defined in this report as the progressive disintegration of a solid by cavitation, abrasion, or chemical action. This report is concerned with: 1) cavitation erosion resulting from the ...
Erosion is defined in this report as the progressive disintegration of a solid by cavitation, abrasion, or chemical action. This report is concerned with: 1) cavitation erosion resulting from the ...
ASTM D3886: Standard Test Method for Abrasion Resistance of Textile Fabrics (Inflated Diaphragm Apparatus)
Abstract: This test method2 covers the determination of the resistance to abrasion of woven and knitted textile fabrics, both conditioned and wet, using the inflated diaphragm tester. This procedure is not applicable to floor coverings.
NOTE 1—Other procedures for measuring the abrasion resistance of textile fabrics are given in Test Met...
NOTE 1—Other procedures for measuring the abrasion resistance of textile fabrics are given in Test Met...
ASTM D3389: Standard Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)
Abstract: This test method covers the determination of the wear resistance of fabrics coated with rubber or plastics to abrasion. The abrasion is measured by mass loss or number of cycles required to wear through the coating to initially expose the base fabric.
The values stated in SI units are to be regarded as the standard. The values given in parenthe...
The values stated in SI units are to be regarded as the standard. The values given in parenthe...
ASTM D4058: Standard Test Method for Attrition and Abrasion of Catalysts and Catalyst Carriers
Abstract: This test method covers the determination of the attrition and abrasion resistance of catalysts and catalyst carriers. It is applicable to tablets, extrudate, spheres, and irregularly shaped particles larger than about 1⁄16 in. (1.6 mm) and smaller than about 3⁄4 in. (19 mm). The materials use...
ASTM F735: Standard Test Method for Abrasion Resistance of Transparent Plastics and Coatings Using the Oscillating Sand Method
Abstract: This test method determines the resistance of transparent plastics and transparent coatings utilized in windows or viewing ports, to surface abrasion using oscillating sand.
The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Exception—The inch-pound units in paren...
The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Exception—The inch-pound units in paren...
ASTM D2228: Standard Test Method for Rubber Property-Relative Abrasion Resistance by Pico Abrader Method
Abstract: This test method covers the determination of the abrasion resistance of vulcanized (thermoset) rubbers, thermoplastic elastomers, and elastomeric and similar materials to a standardized reference system. A standardized set of reference compounds is used to calculate relative abrasion resistance. These reference compounds are also used to determine ...
ASTM F1864: Standard Test Method for Dust Erosion Resistance of Optical and Infrared Transparent Materials and Coatings
Abstract: This test method covers the resistance of transparent plastics and coatings used in aerospace windscreens, canopies, and viewports to surface erosion as a result of dust impingement. This test method simulates flight through a defined particle cloud environment by means of independent control of particle size, velocity, impact angle, mass loading, ...
ASTM D5757: Standard Test Method for Determination of Attrition of FCC Catalysts by Air Jets
Abstract: This test method covers the determination of the relative attrition characteristics of FCC catalysts by means of air jet attrition. Other fine powder catalysts can be analyzed by this test method but the precision of this test method has been determined only for FCC catalysts. It is applicable to spherically or irregularly shaped particles which ra...