Search
Now showing items 11-20 of 1549
API TR 6AF: Technical Report on Capabilities of API Flanges Under Combinations of Load - Third Edition
Abstract: This technical report presents the results of analysis work done in PRAC 86-21 to establish the load capacity of all flanges given in the April 1986 Editions of API 6A and API 6AB. A total of 69 different geometries were analyzed initially. The various loads considered were:
— bolt makeup (preload),
— internal pressure,
R...
— bolt makeup (preload),
— internal pressure,
R...
API SPEC 2H: Specification for Carbon Manganese Steel Plate for Offshore Structures - Ninth Edition
Abstract: This specification covers two grades of intermediate strength steel plates up to 4 in. thick for use in welded construction of offshore structures, in selected critical portions which must resist impact, plastic fatigue ...
API SPEC 6FB: Specification for Fire Test for End Connections - THIRD EDITION; Incorporated ERRATA 1: 08/20/2006, Supplement: 12/2006; ERRATA 2: 12/2008
Abstract: PURPOSE
This specification was formulated to establish procedures for testing and evaluating the pressure-containing performance of API end connections when exposed to fire. Valves, wellhead seals, or ...
This specification was formulated to establish procedures for testing and evaluating the pressure-containing performance of API end connections when exposed to fire. Valves, wellhead seals, or ...
API MPMS 9.2: Manual of Petroleum Measurement Standards Chapter 9.2 Standard Test Method for Density or Relative Density of Light Hydrocarbons by Pressure Hydrometer- Measurement Coordination - Third Edition
Abstract: This test method covers the determination of the density or relative density of light hydrocarbons including liquefied petroleum gases (LPG) having Reid vapor pressures exceeding 101.325 kPa (14.696 psi).
The prescribed apparatus should not be used for materials having vapor pressures higher than 1.4 MPa (200 psi) at the test temperature. This ...
The prescribed apparatus should not be used for materials having vapor pressures higher than 1.4 MPa (200 psi) at the test temperature. This ...
API JOB CODE PART 2: Job Code Classification System Part II - Production Operations and Marketing/Transportation Operations
Abstract: INTRODUCTION
The purpose of this revised job classification system is to provide a standardized method for identifying and classifying jobs within the petroleum refining industry, related ...
The purpose of this revised job classification system is to provide a standardized method for identifying and classifying jobs within the petroleum refining industry, related ...
API SPEC 6FD RUSSIAN: Specification for Fire Test for Check Valves - First Edition
Abstract: It is the purpose of this document to establish the requirements for testing and evaluating the pressure containing performance of API Spec 6A and 6D check valves when exposed to fire. The performance requirements of this ...
API RP 11ER: Recommended Practice for Guarding of Pumping Units - Third Edition
Abstract: This RP is intended to provide safeguards for all persons who are required to work around or on oil well pumping units.
a) These safeguards should prevent bodily injury from contact with moving parts by anyone inadvertently ...
a) These safeguards should prevent bodily injury from contact with moving parts by anyone inadvertently ...
API RP 17U: Recommended Practice for Wet and Dry Thermal Insulation of Subsea Flowlines and Equipment - FIRST EDITION
Abstract: This recommended practice (RP) provides guidance for the performance, qualification, application, quality control, handling, and storage requirements of wet and dry thermal insulation for subsea applications in the petroleum ...
API STD 520 PT II: Sizing, Selection, and Installation of Pressure-relieving Devices Part II-Installation - SIXTH EDITION
Abstract: This standard covers methods of installation for pressure-relief devices (PRDs) for equipment that has a maximum allowable working pressure (MAWP) of 15 psig (1.03 barg or 103 kPAg) or greater. Pressure-relief valves (PRVs) ...
API MPMS 11.2: Manual of Petroleum Measurement Standards Chapter 11.2.1 and 11.2.1M - Compressibility Factors for Hydrocarbons: 0-90 Degrees API Gravity and 638-1074 Kilograms per Cubic Metre Ranges Chapter 11.2.3 and 11.2.3M - Water Calibration of Provers Computer Tape Information and Documentation - First Edition
Abstract: The purpose of this standard is to correct hydrocarbon volumes metered under pressure to the corresponding volumes at the equilibrium pressure for the metered temperature. This standard contains compressibility factors ...