UL 486D BULLETIN

UL - UL

UL Standard for Safety Sealed Wire Connector Systems - COMMENTS DUE: NOVEMBER 15, 2008

Organization:

Year: 2008

Abstract: The requirements in this standard cover sealed wire connector systems, including insulating caps, covers, resins, tubing, and tapes provided with, or for use with, specific wire connectors. These systems are intended for wet or damp locations, and other installations such as direct burial, below grade, or above grade where protected from direct exposure to sunlight. The wire connectors covered by these requirements are intended for use with copper conductor, aluminum conductor, or both in accordance with installations covered by the National Electrical Code, NFPA 70; the Canadian Electrical Code, Part I, C22.1; and NOM 001 SEDE, Standard for Electrical Installations.
Note 1 These wire connector systems have not been evaluated for direct exposure to sunlight. Additional performance considerations to show equivalency to the connected conductors should be considered for UV exposure.
Note 2 These wire connector systems may also be used indoors.
These requirements also cover sealed wire connector systems intended for use with single or multiple conductor underground feeder cable, golf course sprinkler cable, underground low energy cable, irrigation cable, or other cable with insulation acceptable for direct burial, below grade use, or wet locations.
These requirements apply to sealed wire connector systems intended for use with 30 AWG (0.05 mm²) through 2 000 kcmil (1 012 mm²) conductors with currents not exceeding the ampacity of insulated conductors rated either 75 °C (167 °F) or 90 °C (194 °F) and intended for use at 600 V or less.
For products intended for use in Canada, general requirements are given in CAN/CSA-C22.2 No. 0.

URI: http://yse.yabesh.ir/std;jsein=a/handle/yse/230295

Collections :

UL - UL

Show full item record

contributor author	UL - UL
date accessioned	2017-09-04T18:48:58Z
date available	2017-09-04T18:48:58Z
date copyright	39736
date issued	2008
identifier other	ANKKHCAAAAAAAAAA.pdf
identifier uri	http://yse.yabesh.ir/std;jsein=a/handle/yse/230295
description abstract	The requirements in this standard cover sealed wire connector systems, including insulating caps, covers, resins, tubing, and tapes provided with, or for use with, specific wire connectors. These systems are intended for wet or damp locations, and other installations such as direct burial, below grade, or above grade where protected from direct exposure to sunlight. The wire connectors covered by these requirements are intended for use with copper conductor, aluminum conductor, or both in accordance with installations covered by the National Electrical Code, NFPA 70; the Canadian Electrical Code, Part I, C22.1; and NOM 001 SEDE, Standard for Electrical Installations. Note 1 These wire connector systems have not been evaluated for direct exposure to sunlight. Additional performance considerations to show equivalency to the connected conductors should be considered for UV exposure. Note 2 These wire connector systems may also be used indoors. These requirements also cover sealed wire connector systems intended for use with single or multiple conductor underground feeder cable, golf course sprinkler cable, underground low energy cable, irrigation cable, or other cable with insulation acceptable for direct burial, below grade use, or wet locations. These requirements apply to sealed wire connector systems intended for use with 30 AWG (0.05 mm²) through 2 000 kcmil (1 012 mm²) conductors with currents not exceeding the ampacity of insulated conductors rated either 75 °C (167 °F) or 90 °C (194 °F) and intended for use at 600 V or less. For products intended for use in Canada, general requirements are given in CAN/CSA-C22.2 No. 0.
language	English
title	UL 486D BULLETIN	num
title	UL Standard for Safety Sealed Wire Connector Systems - COMMENTS DUE: NOVEMBER 15, 2008	en
type	standard
page	22
status	Active
tree	UL - UL:;2008
contenttype	fulltext