درباره ما
TAPPI - TAPPI: Recent submissions
Now showing items 481-500 of 533
-
TAPPI TIP 0304-38
Abstract: There are numerous chemicals and chemical compounds used in manufacturing and industrial processes. Some of these chemicals and compounds can be hazardous. For the sake of everyone's health and safety, workers must be ...Subject(s) : Chemicals , Hazardous material , Hazards , Materials handling , Safety , -
TAPPI UM 242
Abstract: This method for shive determination makes no attempt to classify the undesirable material in detail, but such a refinement should be within the reach of any user of the method if desired. The dimensional limits dividing ...Subject(s) : Classifiers , Mechanical pulps , Pulps , Shives , -
TAPPI T 489 OM
Abstract: This test method covers a procedure used to measure the resistance to bending of paper and paperboard.
This test method is used to determine the bending moment required to deflect the free end of a 38 mm (1.5 in.) wide ... -
TAPPI UM 822
Abstract: This procedure is to provide basic instructions for subjective testing of the corrugated bond at both the single facer and doublebacker glue lines. The combined board should be allowed to cool for approximately 10 minutes ... -
TAPPI T 809 OM
Abstract: This method describes a procedure for measuring the crushing resistance of a laboratory fluted strip of corrugating medium, and provides a means of estimating, in the laboratory, the potential flat crush resistance of a ...Subject(s) : Compressibility , Compression strength , Corrugated boards , Corrugating medium , Flat crush tests , -
TAPPI TIP 0606-27
Abstract: The current TIP provides basic information for personnel to unload and store bulk concentrated caustic soda safely. It is vitally important that any new bulk concentrated caustic soda facility design be undertaken with the ...Subject(s) : Environments , Materials handling , Safety , Sodium hydroxide , Storage , -
TAPPI T 261 CM
Abstract: This method measures the weight percent fines content of paper stock or of pulp samples by means of a single-screen classifier. A modified procedure permits the use of the apparatus to measure the tendency of the fines ...Subject(s) : Weight fraction fines , Weight percent fines , Wet screening , -
TAPPI T 456 OM
Abstract: This method describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
This procedure is applicable to papers and paperboard (excluding corrugated board) ...Subject(s) : Paper , Paperboard , Saturation , Tensile strength , Tissue papers , Toweling papers , Wet strength , -
TAPPI TIP 0304-18
Abstract: This technical information paper is intended to provide basic instructions for conducting ink viscosity checks at the plant's presses. Quality demands are ever increasing; thus, greater emphasis must be placed upon every ...Subject(s) : Flexography , Ink , Viscosity , -
TAPPI TIP 0404-58
Abstract: This TIP discusses general guidelines for the proper installation and operation of steam showers at the wet end of paper machines.Subject(s) : Dryers , Fogging , Forming , Heating equipment , Moisture , Press sections , Profiles , Showers , Steam , Troubleshooting , Vacuum , -
TAPPI TIP 0305-47
Abstract: By the very nature of running multiple "out" on a rotary diecutter, the blank size of each individual diecut will be small and quite often at or close to press and stacker minimums. As many of these same blanks can also ...Subject(s) : Dieboard , Diecut , Press , Stackers , -
TAPPI T 551 OM
Abstract: This method describes a procedure for measuring the thickness of a single sheet of paper or paperboard using soft synthetic rubber platens against the paper to minimize the effect of surface roughness. This method is not ... -
TAPPI TIP 0402-34
Abstract: This document was created by a TAPPI Task Group to provide information and guidelines for nondestructive testing (NDT) of reel-spool journals used in paper mills. The document describes reel-spool design concepts, failures, ...Subject(s) : Bearings , Inspection , Nondestructive tests , Paper machines , Reels , Shafts , Spools , Testing , -
TAPPI T 1014 OM
Abstract: This test method covers the determination of the moisture sensitivity of fiber glass mat binder systems.Subject(s) : Fiber glass mats , Moisture sensitivity , Sensitivity ,