درباره ما
SAE - SAE International: Recent submissions
Now showing items 521-540 of 16264
-
Hydraulic Hose Fittings
Abstract: This SAE Standard provides general and dimensional specifications for the most common hose fittings used in conjunction with hydraulic hoses specified in SAE J517 and utilized in hydraulic systems on mobile and stationary ... -
H-Point Machine (HPM-II) - Procedure for H-Point Determination - Benchmarking Vehicle Seats
Abstract: Benchmarking is used to discover the design intent measurements for seating compartments in vehicles when these measurements are either unknown or are specified using differing measurement procedures.This document provides ... -
Aircraft Deicing Vehicle - Self-Propelled
Abstract: This SAE Aerospace Recommended Practice (ARP) covers requirements for a self-propelled, boom-type aerial device, equipped with an aircraft deicing/anti-icing fluid spraying system. The unit shall be highly maneuverable for ... -
Optical Warning Devices for Authorized Emergency, Maintenance, and Service Vehicles
Abstract: This document provides design guidelines, test procedure references, and performance requirements for omnidirectional and selective coverage optical warning devices used on authorized emergency, maintenance, and service ... -
Color Specification
Abstract: This SAE Standard defines and provides a means for the control of colors employed in motor vehicle external lighting equipment, including lamps and reflex reflectors. The document applies to the overall effective color of ... -
Fuel Tank Filler Cap and Cap Retainer
Abstract: This SAE Standard was developed primarily for passenger car and truck applications for the sizes indicated, but it may be used in marine, industrial, and similar applications. -
Design and Performance Specifications for a Generic Buck Representing a Small Family Car Used in the Assessment of Pedestrian Dummy Whole Body Impact Response
Abstract: This Information Report addresses the design and performance specifications for a generic buck to be used in full-scale vehicle to pedestrian tests conducted to evaluate pedestrian dummy performance. Specifically, the buck ... -
Test Procedure for Internal Heat Exchangers of Mobile Air-Conditioning Systems with R-134a or R-1234yf Refrigerant
Abstract: The purpose of this SAE Standard is to define a common set of thermodynamic test conditions to evaluate internal heat exchangers for use with R-134a and R-1234yf refrigerants in mobile air-conditioning systems. This standard ... -
Fuel Tank Filler, Capless Closure
Abstract: This SAE Recommended Practice was developed primarily for passenger car and truck applications, but it may be used in marine, industrial, and similar applications. -
Automotive Gasolines
Abstract: This SAE Recommended Practice summarizes the composition of modern automotive gasolines, the significance of their physical and chemical characteristics, and the pertinent test methods for defining or evaluating these properties. -
Welded, Flash-Controlled, Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, Beading, Forming, and Brazing
Abstract: This SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality ... -
Active Safety Bicyclist Test Targets Recommendation
Abstract: The goal of the Bicyclist Test Mannequin Task Force is to develop standard specifications/requirements for bicyclist test mannequins (one adult and one child) that are representative of real bicyclists to the sensors used ... -
Brake Pads, Lining, Disc, and Drum Wear Measurements
Abstract: This Recommended Practice provides a common method to measure wear of friction materials (brake pad assemblies and brake shoes) and their mating parts (brake disc or brake drum). These wear measurements apply to brakes ... -
Heavy Duty Truck and Bus Electrical Circuit Performance Requirement for 12/24-Volt Electric Starter Motors
Abstract: The scope of this SAE Recommended Practice is to describe a design standard to define the maximum recommended voltage drop for starting motor main circuits, as well as control system circuits, for 12- through 24-V starter systems. -
Permanently or Semi-Permanently Installed Diagnostic Communication Devices
Abstract: The scope of the document is to define communication best practices in order to minimize problems for the vehicle owner when installing equipment which has a permanently or semi-permanently diagnostic CAN communication ... -
Wheel Roll on Rim Criteria for Aircraft Applications
Abstract: This SAE Aerospace Recommended Practice (ARP) is to provide a recommended minimum laboratory roll performance for main landing gear aircraft wheels without tires installed and applies to both bolted and lock-ring wheel ... -
Automotive Gear Lubricant Viscosity Classification
Abstract: This SAE Standard defines the limits for a classification of automotive gear lubricants in rheological terms only. Other lubricant characteristics are not considered. -
Technical Information Report on Automotive Battery Recycling
Abstract: This document will focus on the language used to describe batteries at the end of battery or vehicle life as batteries are transitioned to the recycler, dismantler, or other third party. This document also provides a ... -
Wireless Power Transfer for Light-Duty Plug-in/Electric Vehicles and Alignment Methodology
Abstract: The Recommended Practice SAE J2954 establishes an industry-wide specification that defines acceptable criteria for interoperability, electromagnetic compatibility, EMF, minimum performance, safety, and testing for wireless ... -
Misfire Generator Functional Requirements
Abstract: The intent of the specification is to present a functional set of requirements which define the user and hardware interfaces while providing sufficient capability to meet the misfire patterns for compliance demonstration ...