Now showing items 301-320 of 1083

    • ASME A17.6 

      Type: standard
      Source: ASME - ASME International:;2010
      Organization : ASME - ASME International
      Abstract: This Standard covers the means and members of suspension, compensation, and governor systems for elevators within the scope of ASME A17.1/CSA B44.
      NOTE: It must be determined by the individual working committees as to ...
    • ASME B16.48 

      Type: standard
      Source: ASME - ASME International:;2015
      Organization : ASME - ASME International
      Abstract: This Standard covers pressure–temperature ratings, materials, dimensions, tolerances, marking, and testing for operating line blanks in sizes NPS 12 through NPS 24 for installation between ...
    • ASME B94.19 

      Type: standard
      Source: ASME - ASME International:;2009
      Organization : ASME - ASME International
      Abstract: This Standard covers high speed steel milling cutters and end mills of one piece construction as listed in Tables 1 through 62. It also includes general definitions, sizes, and tolerances.
    • ASME PALD INTERPRETATIONS 

      Type: standard
      Source: ASME - ASME International:;1997
      Organization : ASME - ASME International
      Abstract: Scope:
      This publication includes all of the replies issued between the indicated dates by the Secretary for the ASME PALD Committee, Safety Standards for Portable Automotive Lifting ...
    • ASME MFC-13M 

      Type: standard
      Source: ASME - ASME International:;2014
      Organization : ASME - ASME International
      Abstract: SCOPE AND FIELD OF APPLICATION
      For steady-state flow of fluid in a closed conduit, the only conserved parameter is the mass rate of flow, qm. If the mass density is known, the volume rate of flow, ...
    • ASME QAI-1 

      Type: standard
      Source: ASME - ASME International:;2016
      Organization : ASME - ASME International
      Abstract: FOREWORD
      The 2016 Edition of ASME QAI-1 incorporates the 2010 Edition of QAI-1 and revisions and additions approved by the QAI Standards Committee since the publication of the 2010 Edition. This Standard ...
    • ASME B31.8S 

      Type: standard
      Source: ASME - ASME International:;2012
      Organization : ASME - ASME International
      Abstract: This Code applies to onshore pipeline systems constructed with ferrous materials and that transport gas. The principles and processes embodied in integrity management are applicable to all pipeline systems.
      This Code ...
    • ASME MFC-21.1 

      Type: standard
      Source: ASME - ASME International:;2015
      Organization : ASME - ASME International
      Abstract: This Standard establishes common terminology and provides guidelines for the quality, description, principle of operation, selection, operation, installation, and flow calibration of capillary tube thermal mass flowmeters ...
    • ASME B16.9 

      Type: standard
      Source: ASME - ASME International:;2012
      Organization : ASME - ASME International
      Abstract: General
      This Standard covers overall dimensions, tolerances, ratings, testing, and markings for factory-made wrought buttwelding fittings in sizes NPS 12 through NPS 48 (DN ...
    • ASME B30.19 

      Type: standard
      Source: ASME - ASME International:;2011
      Organization : ASME - ASME International
      Abstract: The ASME B30 Standard contains provisions that apply to the construction, installation, operation, inspection, testing, maintenance, and use of cranes and other lifting and material-handling related equipment. For the ...
    • ASME STP-NU-059 

      Type: standard
      Source: ASME - ASME International:;2013
      Organization : ASME - ASME International
      Abstract: OBJECTIVE
      ASME Standards Technology, LLC has sponsored a thorough review of current allowable stress values in ASME Boiler and Pressure Vessel Code, Section III, Division I, Subsection NH, and to ...
    • ASME PTC 6S REPORT 

      Type: standard
      Source: ASME - ASME International:;2009
      Organization : ASME - ASME International
      Abstract: Sections 3 through 5 of this Report present general recommendations for instrumentation and test planning. These recommendations are based on current industry practice for the periodic determination of turbine-cycle ...
    • ASME A112.19.1 

      Type: standard
      Source: ASME - ASME International:;2013
      Organization : ASME - ASME International
      Abstract: This Standard covers enamelled cast iron and enamelled steel plumbing fixtures and specifies requirements for materials, construction, performance, testing, and markings.
      This Standard covers the following plumbing ...
    • ASME PTC 12.1 

      Type: standard
      Source: ASME - ASME International:;2015
      Organization : ASME - ASME International
      Abstract: This Code applies to all horizontal and vertical heaters except those with partial pass full-length drain cooling zones. The heater design is based on a specific operating condition that includes flow, temperature, and ...
    • ASME B18.2.3.2M 

      Type: standard
      Source: ASME - ASME International:;2005
      Organization : ASME - ASME International
      Abstract: (a) This Standard covers the complete dimensional and general data for metric formed hex screws recognized as American National Standard. Formed hex screws are cold formed products with fully upset (non-trimmed) heads. ...
    • ASME STP-NU-020 

      Type: standard
      Source: ASME - ASME International:;2008
      Organization : ASME - ASME International
      Abstract: Part I Base Metal - Databases summarizing the creep-rupture properties of alloy 800H and its variants were reviewed and referenced. For the most part, the database was judged to be adequate to meet the needs for time-dependent ...
    • ASME B30.10 

      Type: standard
      Source: ASME - ASME International:;2014
      Organization : ASME - ASME International
      Abstract: SCOPE EXCLUSIONS
      Any exclusion of, or limitations applicable to the equipment, requirements, recommendations, or operations contained in this Standard are established in the affected volume's scope. ...
    • ASME B30.21 INTERPRETATIONS 

      Type: standard
      Source: ASME - ASME International:;1992
      Organization : ASME - ASME International
      Abstract: Scope:
      This publication includes all of the written replies issued between the indicated dates by the Secretary, speaking for the ASME B30 Committee, Safety Standards for Cableways, ...
    • ASME MFC-7M 

      Type: standard
      Source: ASME - ASME International:;2006
      Organization : ASME - ASME International
      Abstract: SCOPE AND FIELD OF APPLICATION
      This Standard applies only to the steady flow of single-phase gases and deals with devices for which direct calibration experiments have been made, sufficient in number and quantity ...
    • ASME A112.3.1 

      Type: standard
      Source: ASME - ASME International:;2007
      Organization : ASME - ASME International
      Abstract: This Standard establishes material, dimensions, mechanical, and physical (including marking) requirements for socket-type, seam-welded, stainless steel pipe, fittings, joints, and drains for use in plumbing sanitary and ...