درباره ما
ASME - ASME International: Recent submissions
Now showing items 441-460 of 1083
-
ASME B107.110
Abstract: This Standard provides performance and safety requirements for socket wrenches (sockets), handles used with these wrenches, nutdrivers, and attachments used with socket wrenches, hereinafter collectively referred to as ... -
ASME B18.15
Abstract: This Standard is limited to dimensions and capacities for forged threaded eyebolts intended primarily for lifting applications, and covers the following types and styles.
Type 1 , Plain pattern (straight shank) ... -
ASME STP-PT-065
Abstract: PURPOSE AND USE
Industry standards for dead legs in biopharmaceutical processing equipment have been in place for over a decade. A dead leg is defined as an area of entrapment in a vessel or piping run ... -
ASME B18.16.6
Abstract: This Standard covers the complete general, dimensional, mechanical, and performance requirements (proof load, prevailing torque, and torque-tension) for carbon steel, inch series nylon insert locknuts of grades N2, N5, and ... -
ASME STP-PT-056
Abstract: INTRODUCTION
This project resulted from ASME Pressure Technology Codes and Standards (PTCS) Standards Committee requests to identify, prioritize and address technology gaps in PTCS Codes, Standards and ... -
ASME A112.19.15
Abstract: This Standard establishes material, mechanical, electrical, marking, and testing requirements for bathtubs/ whirlpool bathtubs with doors that are made water tight by the use of a pressure seal. It addresses the functional ... -
ASME N509 INTERPRETATIONS
Abstract: Scope:
This publication includes all of the written replies issued between the indicated dates by the Secretary, speaking for the ASME CONAGT Committee, Committee on Nuclear Air ... -
ASME B30.14
Abstract: Volume B30.14 includes provisions that apply to the construction, installation, operation, inspection, testing, and maintenance of side boom tractors powered by an internal combustion engine used for pipe laying or ... -
ASME B18.2.5M
Abstract: This Standard covers the complete dimensional and general data for coarse thread metric series 12-point flange screws recognized as American National Standard. The inclusion of dimensional data in this Standard is not ... -
ASME PTC 40
Abstract: OBJECT AND SCOPE
The performance of a flue gas desulfurization system (FGDS) is defined to be the characterization of inputs and outputs (see Fig. 1.1). This may include, but is not necessarily limited to, the ... -
ASME PTC 4
Abstract: The rules and instructions presented in this Code apply to fired steam generators. These include coal, oil, and gas-fired steam generators as well as steam generators fired by other hydrocarbon fuels. The scope also includes ... -
ASME CA-1
Abstract: This Standard specifies the requirements for accreditation and certification of organizations supplying products and/or services that are intended to conform to the requirements of ASME standards listed in Table 1. -
ASME B16.12
Abstract: This Standard for cast iron threaded drainage fittings covers
(a) sizes and method of designating openings in reducing fittings
(b) marking
(c) material
(d) dimensions ... -
ASME B18.31.2
Abstract: This Standard covers the complete dimensional and general data for continuous thread and double-end inch-dimensioned studs recognized as American National Standard. The following configurations are covered:
continuous ... -
ASME STP-PT-073
Abstract: FOREWORD
The purpose of this report is to align stress intensification and flexibility factors for metallic pipes used in ASME's Pressure Piping Codes (B31) and Boiler and Presure Vessel Code (B&PVC) ... -
ASME B31J
Abstract: Rules for this Code Section have been developed considering the needs for applications which include piping typically found in electric power generating stations, in industrial and institutional plants, geothermal heating ... -
ASME A112.1016
Abstract: This Standard applies to automatic compensating valves intended to be installed at the point of use, where the user has access to flow or final temperature controls, and where no further mixing occurs downstream of the ... -
ASME PTC 8.2
Abstract: Prepared in accordance with ASME PTC 1 on General Instructions, this Code provides standard directions for conducting; and reporting performance tests of centrifugal pumps, including those of the mixed flow and axial ... -
ASME B36.10M
Abstract: This Standard covers the standardization of dimensions of welded and seamless wrought steel pipe for high or low temperatures and pressures.
The word pipe is used, as distinguished from tube, to apply ...