درباره ما
ASME - ASME International: Recent submissions
Now showing items 481-500 of 1083
-
ASME B16.34
Abstract: General
This Standard applies to new construction and covers pressure–temperature ratings, dimensions, tolerances, materials, nondestructive examination requirements, testing, and marking for ... -
ASME B4.2
Abstract: This standard describes the ISO system of limits and fits for mating parts as it is approved for general engineering usage in the United States of America. It establishes: (1) the designation symbols used to define specific ... -
ASME B29.21M
Abstract: An ANSI B29 Subcommittee was established in 1975 to develop a standard which would aid municipalities and others in specifying chains for water and sewage treatment plants. This Standard is the result of that effort. ... -
ASME A17.1 HDBK
Abstract: The ASME A17.1/CSA B44, Safety Code for Elevators and Escalators, and ASME A17.7/CSA B44.7, Performance Based Safety Code for Elevators and Escalators, are the accepted guides for design, construction, ... -
ASME PTC 12.5
Abstract: The scope of this Code includes instruments, calculation techniques, and methods to determine the steady state performance of single phase heat exchangers at both test conditions and reference conditions and reference ... -
ASME B1.20.5
Abstract: The scope of this Standard is to provide information regarding practical dryseal thread inspection methods and commonly used gages for production evaluation purposes. All dimensions are in inches unless otherwise ... -
ASME CSD-1
Abstract: The rules of this Standard cover requirements for the assembly, installation, maintenance, and operation of controls and safety devices on automatically operated boilers directly fired with gas, oil, gas-oil, or electricity, ... -
ASME PTC 20.1
Abstract: OBJECT AND SCOPE
The purposes of this Code are:
To establish test procedures for determining performance characteristics of speed and load governing systems applicable to the equipment covered under ... -
ASME B16.15 INTERPRETATIONS
Abstract: Scope:
As a service to persons who use the B16 Standards, the B16 Committee renders interpretations of the requirements upon request. The procedure for requesting an interpretation ... -
ASME PTC 23
Abstract: This Code provides rules for determining the performance of all referenced cooling equipment with regard to the thermal capability, deviation from design thermal capability, or deviation from design coldwater temperature. ... -
ASME B29.1
Abstract: FOREWORD
The original design of precision roller chain dates back to the late 1890s, although various types of drive chains have been in use for centuries. The early automobiles used roller chains ... -
ASME B18.18
Abstract: This quality focused Standard establishes in-process and final inspection requirements for fastener products as well as a receiving inspection plan for fastener purchasers. This Standard identifies four categories, recognizing ... -
ASME STP-NU-068
Abstract: INTRODUCTION
To better determine the impacts of using A193 Grade B7 bolts in stainless steel flanges installed in a Boiler Water Reactor (BWR) sodium pentaborate (NaPB) systems, quantification of the ... -
ASME PTC 18
Abstract: This Code applies to all sizes and types of hydraulic turbines or pump-turbines. It defines methods for ascertaining performance by measuring flow rate (discharge), head, and power, from which efficiency may be determined. ... -
ASME B18.6.5M
Abstract: This Standard covers the complete general, dimensional, and performance requirements for the various types of slotted and recessed head metric tapping screws recognized as standard. Also included are appendices that provide ... -
ASME B31Q
Abstract: This Standard establishes the requirements for developing and implementing an effective Pipeline Personnel Qualification Program (qualification program) utilizing a combination of technically based data, accepted industry ... -
ASME B89.1.9
Abstract: This Standard specifies the most important design and metrological characteristics of gage blocks with a rectangular or square cross-section and a nominal length ln ranging from 0.5 mm to 1 000 mm for metric ... -
ASME N509
Abstract: This Standard covers requirements for the design, construction, and qualification and acceptance testing of the air-cleaning units and components which make up Engineered Safety Feature (ESF) and other high efficiency ... -
ASME B31.12
Abstract: This Code is applicable to piping in gaseous and liquid hydrogen service and to pipelines in gaseous hydrogen service. This Code is applicable up to and including the joint connecting the piping to associated pressure ... -
ASME B1.13M
Abstract: This Standard contains general metric standards for a 60 deg symmetrical screw thread with a basic ISO 68-1 profile designated M profile. The M profile threads of tolerance class 6H/6g are intended for metric applications ...