درباره ما
ACI - American Concrete Institute: Recent submissions
Now showing items 381-400 of 636
-
ACI 551.1R
Abstract: Introduction
According to ACI 116R, "Tilt-up construction is a technique for casting concrete elements in a horizontal position at the jobsite and tilting them to their final position in the structure," ...Subject(s) : finish , insert , panel , release agent , sandwich panel , tilt-up , -
ACI ASCC-1
Abstract: Foreword
Safety
Construction can be a hazardous business. With proper training procedures, hazard inspections, and rules enforcement, however, the hazards can be greatly ... -
ACI 523.2R
Abstract: The recommendations of this Guide apply to precast reinforced cellular concrete units, which are designed and factoryproduced for use in structures. These recommendations are based largely on the experience gained with a ...Subject(s) : cellular concretes , concrete construction , concrete slabs , deflection , floors , lightweight concretes , precast concrete , prefabrication , roofs , structural design , thermal conductivity , walls , -
ACI 228.1R
Abstract: In-place tests are performed typically on concrete within a structure, in contrast to tests performed on molded specimens made from the concrete to be used in the structure. Historically, they have been called nondestructive ...Subject(s) : coefficient of variation , compressive strength , construction , in-place tests , nondestructive tests , safety , sampling , statistical analysis , -
ACI 318
Abstract: PREFACE TO ACI 318-14
The "Building Code Requirements for Structural Concrete" ("Code") provides minimum requirements for the materials, design, and detailing of structural concrete buildings and, where applicable, ... -
ACI 362.1R
Abstract: The purpose of this guide is to provide specific information on several of the design aspects and the construction of parking structures that differentiates them from other concrete structures. This guide should be used ... -
ACI 363.2R
Abstract: This guide discusses QC and testing practices of HSC. HSC usually is associated with structures that have been optimized for performance. Therefore, a high degree of confidence in concrete quality should be achieved through ...Subject(s) : acceptance criteria , compressive strength , concrete placement , creep , curing , delivery , modulus of elasticity , quality assurance , quality control , sampling , shrinkage , statistical concepts , strength evaluation , testing , trial batching , -
ACI 548.4
Abstract: This Specification covers the materials and procedures for construction of styrene-butadiene latex-modified concrete (LMC) overlays for new construction as well as repair and rehabilitation of existing bridge decks and ... -
ACI 364.6T
Abstract: Introduction
The performance of a reinforced concrete repair depends significantly on the condition of concrete in the reinforcement vicinity and on the quality of (re-)encapsulation. The extent of ...Subject(s) : corrosion , reinforcing steel , repair , ring anode effect , surface preparation , -
ACI 549.2R
Abstract: INTRODUCTION
Thin reinforced cementitious products are used widely today in a variety of applications worldwide. Thin reinforced cementitious products are strong, possess superior deformability ... -
ACI ITG-7
Abstract: Work specified—This Specification designates standard tolerances for structural and architectural precast concrete members. Tolerances are provided for individual members and their erection. The indicated ...Subject(s) : alignment , construction , erection tolerances , precast concrete , prestressed concrete , product tolerances , reinforcement , specification , -
ACI 341.2R
Abstract: General
The stated objectives of seismic design provisions in major codes have evolved considerably over the last 20 years. The initial focus of preventing structural collapse under the design earthquake ... -
ACI 330R
Abstract: This guide is based on the current knowledge and practices for the design, construction, and maintenance of concrete parking lots placed on the ground. It emphasizes the aspects of concrete pavement technology that are ...Subject(s) : air entrainment , coatings , compacting , concrete construction , concrete durability , concrete pavements , concrete slabs , curing , dowels , drainage , economics , finishing , joint sealants , joints , load transfer , loads (forces) , maintenance , parking facilities , quality control , reinforcing steels , repairs , resurfacing , soils , specifications , structural design , subbases , subgrades , thickness , tolerances , welded-wire fabric , workability , -
ACI 503.5R
Abstract: GENERAL
This guide is intended to aid the engineer, contractor, and architect in choosing a proper polymer adhesive for adhesive bonding applications encountered in joining concrete members in construction, ...Subject(s) : acrylic resias , adheslves , bolts , bonding , cpoxy resins , fire resistance , fresh concretes , grouting , latex , loads (forces) , methacrylate , plastics , polymers , and reslas , polyester , polysulfide , polyurethane , repairs , sealing , serviceability , silicone resins , styrene-butadience resins , toxicity , vinyl acetate , water-berne adheslves , -
ACI SP-183
Abstract: At ACI’s 1996 fall convention in New Orleans, La., ACI-ASCE Joint Committee 421, Design of Reinforced Slabs, sponsored two technical sessions. The focus of the morning session was “Design of Two-way Slabs using ...Subject(s) : analysis , design , elastic frames , history , reinforced concrete slabs , -
ACI 562M
Abstract: The scope, purpose, applicability, exclusions, interpretation, principles, language, and units of measure are defined in this chapter.
The "existing building code" refers to the code adopted by a jurisdiction that ... -
ACI 304.1R
Abstract: INTRODUCTION
This report on preplaced aggregate (PA) concrete for structural and mass concrete applications describes practices as developed over many years by engineers and contractors in the successful ...Subject(s) : fluidizing , grout , heavyweight concrete , inserts , preplaced aggregate concrete , underwater construction ,