درباره ما
Browsing AWWA - American Water Works Association by Issue Date
Now showing items 1-20 of 296
-
AWWA C502
Abstract: This standard describes post-type, dry-barrel fire hydrants with compression shutoff (opening against or with the pressure) or gate shutoff for use in water supply service in all climates, including those where freezing ... -
AWWA C651
Abstract: This standard describes essential procedures for the disinfection of new and repaired potable water mains. New water mains shall be disinfected before they are placed in service. Water mains taken out of service for ... -
AWWA C503
Abstract: This standard pertains to the various types and classes of wet-barrel fire hydrants for use in water-supply service in areas where the climate is mild and freezing temperatures do not occur. A wet-barrel hydrant has one ... -
AWWA C213
Abstract: This standard describes the material and application requirements for fusion-bonded epoxy coatings for the interior and exterior of steel water pipe, special sections, welded joints, connections, and fittings for steel ... -
AWWA C301
Abstract: This standard describes the manufacture of circumferentially prestressed concrete pressure pipe with a steel cylinder and wire reinforcement in sizes 16 in. (410 mm) through 144 in. (3,660 mm). Larger sizes have been ... -
AWWA C210
Abstract: This standard sets minimum requirements for shop‑ and field‑applied, liquid‑epoxy interior linings and exterior coatings used in the water‑supply industry for steel water pipelines installed underground ... -
AWWA C303
Abstract: This standard describes the manufacture of concrete pressure pipe, reinforced with a steel cylinder that is helically wrapped with mild steel bar reinforcement, in sizes ranging from 10 in. through 72 in. (250 mm through ... -
AWWA M9
Abstract: Purpose and Scope
The use of concrete pressure pipe for conveying water and other liquids under pressure has dramatically increased in recent years. Its rugged construction and the natural corrosion ... -
AWWA C104/A21.4
Abstract: This standard describes shop-applied, cement–mortar linings specified in the ANSI*/AWWA C100/A21 series of standards for ductile-iron pipe and ductile-iron and gray-iron fittings for water, wastewater, and reclaimed ... -
AWWA C203
Abstract: This standard provides the minimum requirements for coal-tar protective exterior coatings and interior linings used in the water supply industry for buried steel water pipelines.
AWWA steel pipe coating standards are ... -
AWWA C151/A21.51
Abstract: This standard describes 3-in. through 64-in. (76-mm* through 1,600-mm) ductile-iron pipe, centrifugally cast, for water, wastewater, and reclaimed water systems with push-on joints or mechanical joints. Requirements for ... -
AWWA C700
Abstract: This standard describes the various types and classes of cold-water displacement meters with bronze main cases, in sizes 1/2 in. (13 mm) through 2 in. (50 mm), and the materials and workmanship employed ... -
AWWA C702
Abstract: This standard describes the various types and classes of cold-water compoundType meters in sizes 2 in. (50 mm) through 8 in. (200 mm), and the materials and workmanship used in their fabrication. Compound meters shall ... -
AWWA C105/A21.5
Abstract: This standard describes materials and installation procedures for polyethylene encasement to be applied to underground installations of ductile-iron pipe. This standard also may be used for polyethylene encasement of ... -
AWWA B301
Abstract: This standard describes liquid chlorine for use in water, wastewater, and reclaimed water treatment.
Purpose
The purpose of this standard is to provide the minimum requirements for liquid chlorine, ... -
AWWA B300
Abstract: This standard describes chlorinated lime, calcium hypochlorite, and sodium hypochlorite for use in water, wastewater, and reclaimed water treatment.
Purpose
The purpose of this standard is to provide ... -
AWWA C504
Abstract: This standard establishes minimum requirements for rubber-seated butterfly valves, 3 in. (75 mm) through 72 in. (1,800 mm) in diameter, with various body and end types, for fresh water having a pH range from 6–12 and ... -
-
AWWA B502
Abstract: This standard describes sodium polyphosphate, glassy, for use in the treatment of potable water, wastewater, and reclaimed water. This material is also known as sodium hexametaphosphate, sodium tetrapolyphosphate, and ... -
AWWA C703
Abstract: This standard describes the various types and classes of cold-water fireserviceType meters in sizes 3 in. (80 mm)* through 10 in. (250 mm) and the materials and workmanship used in their fabrication. A fire-service meter ...