درباره ما
ASME - ASME International: Recent submissions
Now showing items 341-360 of 1083
-
ASME B31.5
Abstract: Rules for this Code Section have been developed considering the needs for applications that include piping and heat transfer components for refrigerants and secondary coolants.
This Code prescribes requirements for the ... -
ASME B16.45
Abstract: General
This Standard for cast iron drainage fittings used on self-acrating, one-pipe Sovent® drainage systems, covers the following:
(a) description
(6) sizes and methods for designating ... -
ASME TDP-1
Abstract: This Standard includes recommended practices concerned primarily with the prevention of water damage to steam turbines used for fossil-fuel-fired electric power generation. The practices address damage due to water, wet ... -
ASME B16.4 INTERPRETATIONS
Abstract: AS a service to persons who use the B16 standards, the B16 Committee renders interpretations of the requirements upon request. The procedure for requesting an interpretation is described in the following paragraphs. ... -
ASME B89.1.7
Abstract: This Standard specifies the requirements for steel measuring tapes, with respect to units (SI and U.S. Customary), graduations, numbering, designations, and accuracy requirements. -
ASME PTC 17
Abstract: Application of this Code is limited to engine assemblies as defined in Pars. 1.3.2 and 1.3.3.
Code Engine Assembly. In the absence of specified stipulations the engine assembly to be tested shall consist of ... -
ASME STP-PT-058
Abstract: INTRODUCTION
Post-weld heat treatment (PWHT) is applied to steel assemblies in order to reduce the likelihood of brittle fracture; this is achieved through the combined effect of a reduction in residual ... -
ASME A112.19.7
Abstract: This Standard specifies general requirements, test methods, and markings for whirlpool and air-jetted bathtubs and suction fittings used in hydromassage bathtub systems that incorporate a bathtub and circulation pump. The ... -
ASME PTC 1
Abstract: SCOPE AND ORGANIZATION OF PTCs
Most ASME PTCs are applicable to a specified type of equipment defined by the Code. Theremay be several subcategories of equipment covered by a single code. Types of ... -
ASME STP-NU-039
Abstract: INTRODUCTION
The GEN IV reactor concepts require structural components to operate at high temperatures in a regime where creep damage may occur and cracks may grow. The U.S. Nuclear Regulatory Commission ... -
ASME B5.57
Abstract: This Standard establishes requirements and methods for specifying and testing the performance of CNC lathes and turning centers. In addition to clarifying the performance evaluation of lathes and turning centers, this ... -
ASME B1.8
Abstract: GENERAL AND HISTORICAL
When formulated prior to 1895, regular Acme screw threads were intended to replace square threads and a variety of threads of other forms used chiefly for the purpose of ... -
ASME PASE
Abstract: The scope of this Standard is the standardization of safety and performance requirements for portable automotive service equipment (PASE) including, but not limited to, the following:
(a) attachments, adapters, and ... -
ASME HST-2
Abstract: (a) This Standard establishes performance requirements for hand chain manually operated chain hoists for vertical lifting service involving material handling of freely suspended (unguided) loads, using welded link type ... -
ASME PTC 28
Abstract: OBJECT AND SCOPE
The object of the test shall be to determine various physical and chemical properties of dust. This Code provides procedures for determining these properties and defines the terminology to be used ... -
ASME B29.10M
Abstract: Chains of the type covered by this Standard were introduced in the United States late in the 19th Century. As their popularity increased, the number of chains and manufacturers grew. As one manufacturer developed a ... -
ASME B30.3
Abstract: Any exclusion of, or limitations applicable to the equipment, requirements, recommendations or operations contained in this Standard are established in the affected volume's scope.
PURPOSE
The B30 ... -
ASME B29.15M
Abstract: Chains of the type covered by this Standard were introduced late in the nineteenth century. These chains met with considerable success on material conveyors and elevators. Manufacturers developed and marketed many sizes ... -
ASME PTC 19.3 TW ERTA
Abstract: The Scope of the work of Technical Committee No. 19 on Instruments and Apparatus is to describe the various types of instruments and methods of measurement likely to be prescribed in any of the ASME Performance Test ...