درباره ما
Defence Standards: Recent submissions
Now showing items 61-80 of 43216
-
MIL-DTL-41819/32D
Abstract: This specification is approved for use by all Departments and Agencies of the Department of Defense.
The requirements for acquiring the product described herein shall consist of this specification sheet and the issue ... -
NASA-LLIS-0759
Abstract: Practice:
Critical design features that reduce joint rotation, improve seal features, provide close tolerances, provide for leak checks, and provide venting are used to improve the reliability of ... -
MSFC-PLAN-2889 REV A CHG NOTICE 1
Abstract: This document presents the Quality Plan to be implemented for the Dynamically-Controlled Protein Crystal Growth (DCPCG) hardware and software that is being developed by the University of Alabama in Birmingham (UAB) under ... -
MIL-DTL-15665/91
Abstract: This specification is approved for use by all Departments and Agencies of the Department of Defense.
The requirements for acquiring the product described herein shall consist of this specification sheet and the issue ... -
SMD-5962-95513 REV A
Abstract: This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are ... -
MIL-PRF-19500/607B
Abstract: This specification covers the performance requirements for N-channel, and P-channel, enhancement-mode, MOSFET, power transistor. Four levels of product assurance are provided for each device type as specified in MIL-PRF-19500, ... -
MIL-DTL-62011E
Abstract: This specification covers electrically-operated 24-volt (V), direct current (dc), in-tank fuel pumps capable of delivering 200 gallons per hour (gph) with outlet pressure at 4 pounds per square inch gauge (psig) (see ...Subject(s) : Diesel , Flow , Gallons per hour , Gasoline , Motor , Pressure , -
NASA-LLIS-1859
Abstract: Abstract:
NASA subject experts can speed negotiating contract specifications because they know what is and is not the state-of-the-art. They can avoid including requirements that would delay delivery ...Subject(s) : Systems Engineering and Analysis. , Systems Engineering and Analysis.Level II/III requirements definition , -
SMD-5962-97624 REV B
Abstract: This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are ... -
NACA-TR-648
Abstract: Equations and design charts are given for predicting the downwash angles and the wake characteristics for power-off conditions behind plain and flapped wings of the types used in modern design practice. The downwash charts ...Subject(s) : AERODYNAMIC , ANALYSIS , ANGLES , ASPECT , CHARTS , DESIGN , DISTRIBUTION , DOWNWASH , DRAG , ELLIPTICITY , FLAPS , FORCES , GEOMETRY , LIFT , LOAD , PREDICTION , PRESSURE , RATIO , SPAN , SWEPT , TECHNIQUES , WAKES , WING , WINGS , -
NACA-CB-L5C01
Abstract: A method is given for calculating the stick-fixed neutral point of an airplane with propeller windmilling, flaps neutral, and landing gear retracted. This method differs from those formerly used principally in the procedure ... -
MIL-PRF-83401/7E (1)
Abstract: This specification covers the associated requirements for style RZ070, 6 pin single-in-line package (SIP) resistor networks. This style is available in all characteristics and all resistance tolerances. This specification ... -
A-A-55171C VALID NOTICE 1
Abstract: This CID covers the general requirements for radio frequency interference (RFI) suppression power line filters. These filters consist of capacitors and inductors used in combination with each other and are provided with ... -
SMD-5962-97577 REV A
Abstract: This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are ...