درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 41-60 of 39933
-
Standard Practice for Best Practices for Safe Application of 3D Imaging Technology
Abstract: 3.1 The overall purpose of standards is to document and communicate best practices in the successful and consistent application of 3D imaging technology. When executed effectively, this leads to an enhanced project ... -
Standard Test Method for Blast Resistance of Trash Receptacles
Abstract: 5.1 This test procedure is used to measure two of the main effects of an explosive detonated in a trash receptacle as related to the type and amount of explosive charge and the location where the charge is placed in the ... -
Standard Classification for Program and Project Estimate Summaries
Abstract: 4.1 Program and project estimates are a necessary part of planning and implementing any program of work. 4.2 These estimates are used by persons involved in the planning and management of programs and projects. They are ... -
Standard Test Method for Sensory Analysis—Duo-Trio Test
Abstract: 5.1 The test method is effective for the following test objectives: 5.1.1 To determine whether a perceivable difference results or a perceivable difference does not result, for example, when a change is made in ingredients, ... -
Standard Practice for Use of Control Charts in Statistical Process Control
Abstract: 4.1 This practice describes the use of control charts as a tool for use in statistical process control (SPC). Control charts were developed by Shewhart (2) in the 1920s and are still in wide use today. SPC is a branch of ... -
Standard Test Methods for Evaluating Water-Resistive Barrier (WRB) Coatings Used under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage
Abstract: 4.1 This series of test methods provides a means to evaluate performance of the water-resistive barrier coating when subjected to various physical and environmental conditions. The water-resistive barrier coating is applied ... -
Standard Test Method for Multiangle Color Measurement of Interference Flake Pigmented Materials
Abstract: 5.1 This test method is designed to provide color data obtained from spectral reflectance factors at specific illumination and detection angles for interference pigments. Information presented in this test method is based ... -
Standard Practice for Targeted Defect Detection Using Process Compensated Resonance Testing Via Swept Sine Input for Metallic and Non-Metallic Parts
Abstract: 5.1 PCRT Applications and Capabilities—PCRT has been applied successfully to a wide range of NDT applications in the manufacture and maintenance of metallic and non-metallic parts. Examples of anomalies detected are discussed ... -
Standard Practice for Presentation Format of Elemental Cost Estimates, Summaries, and Analyses
Abstract: 5.1 Significance: 5.1.1 The application of elements (see 3.1.1 and Terminology E833) to the description and the summary and analysis of building construction cost provides a consistency, commonality, and utility through ... -
Standard Guide for Specification, Design, and Verification of Pharmaceutical and Biopharmaceutical Manufacturing Systems and Equipment Science and Risk Based Approach
Abstract: 5.1 Application of the approach described within this guide is intended to satisfy international regulatory expectations in ensuring that manufacturing systems and equipment are fit for intended use, for example, qualified, ... -
Standard Specification for Expanded Polystyrene (“EPS”) Thermal Insulation Boards for Use in Exterior Insulation and Finish Systems (“EIFS”) and EIFS with Drainage
Abstract: This specification is for flat, uncoated expanded polystyrene thermal insulation boards for use in exterior insulation and finish systems (EIFS). The thermal insulation boards shall be made of a particular percentage of ... -
Standard Specification for Voluntary Security Performance of Window and Door Assemblies with Glazing Impact
Abstract: This specification covers voluntary performance requirements and methods of laboratory tests for the resistance to forced entry of window and door assemblies. The capability of window and door assemblies to frustrate ... -
Standard Specification for Nickel-Molybdenum Alloy Rod
Abstract: This specification covers rod of nickel-molybdenum alloys of UNS N10001, N10665, N10675, N10629, and N10624 for use in general corrosive service. The material shall conform to the required chemical composition for nickel, ... -
Standard Specification for Shelter, Electrical Equipment, Lightweight
Abstract: This specification covers two types of lightweight electrical equipment shelters designed for transport on both the M1037 and M1097 high mobility multipurpose wheeled vehicle (HMMWV) by rail, air, marine, and highway when ... -
Standard Test Method for Field Pull Testing of an In-Place Wall Assembly with an Exterior Insulation and Finish System (EIFS) or EIFS with Drainage System
Abstract: 4.1 The purpose of this test method is to assess the installation adequacy and the overall effects of service-related deterioration (moisture, etc.) on the wall assembly as opposed to small localized areas of degradation. ... -
Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems
Abstract: 5.1 These test methods are intended to evaluate the ability of the grease duct enclosure system to do the following: 5.1.1 Resist the effects of a standardized fire exposure, 5.1.2 Retain its integrity, or 5.1.3 Exhibit ... -
Standard Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate-Scale, Multi-story Test Apparatus
Abstract: 5.1 This test method provides for the following measurements and evaluations: 5.1.1 Movement capacity of the perimeter fire barrier. 5.1.2 Loadbearing capacity of the perimeter joint protection is optional. 5.1.3 Ability ... -
Standard Test Method for Determination of Particles Resulting from the Attrition of Granular Pesticides
Abstract: 5.1 This test method is designed specifically for granular pesticide formulations. 5.2 This test method helps provide information on health hazards likely to arise from exposures by the inhalation route. It can be of use ...