درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 381-400 of 39933
-
Standard Specification for AMS (α-Methylstyrene)
Abstract: This specification establishes the requirements for AMS (alpha-Methylstyrene). Sampled specimens shall conform to the following physical and chemical properties: minimum AMS content; maximum phenol content; maximum polymer ... -
Standard Guide for Selecting Cleaning Agents and Processes
Abstract: 5.1 This guide is to be used by anyone developing cleaning requirements for specifications for manufacturing, maintenance, or overhaul. This guide has been designed to be application specific for each cleaning task and to ... -
Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fischer Titration
Abstract: 5.1 A knowledge of the water content is important in the manufacturing, purchase, sale, or transfer of petroleum products to help in predicting their quality and performance characteristics. 5.2 The presence of moisture ... -
Standard Specification for Asphaltic Plug Joints for Bridges
Abstract: This specification covers the standards the material, testing and application requirements for a field molded asphaltic plug joint (APJ) used in expansion joint sealing on asphalt concrete overlay and portland cement ... -
Standard Guide for Direct Push Soil Sampling for Environmental Site Characterizations
Abstract: 5.1 Direct Push Soil Sampling is used extensively in environmental site characterization of soils below ground surface and can also be used for subsurface geotechnical site characterization (3, 7-13). Limited early studies ... -
Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
Abstract: 5.1 Flexural properties determined by this test method are especially useful for quality control and specification purposes. 5.2 This test method is recommended for those materials that do not fail within the strain limits ... -
Standard Practice for Use of Scrap Tires in Civil Engineering Applications
Abstract: 4.1 This practice is intended for use of scrap tires including: tire-derived aggregate (TDA) comprised of pieces of scrap tires, TDA/soil mixtures, tire sidewalls, and whole scrap tires in civil engineering applications. ... -
Standard Specification for Martensitic Stainless Steel Forgings and Forging Stock for High-Temperature Service
Abstract: This specification covers martensitic chromium stainless steel forgings, forged bars, and forging stock for high-temperature service. The mechanical properties are developed by suitable heat treatment, as indicated for ... -
Standard Specification for Extruded and Compression Molded Basic Shapes Made from Thermoplastic Polyester (TPES)
Abstract: This specification covers requirements and test methods for the material, dimensions, and workmanship, and the properties of extruded and compression molded plate, rod and tubular bar manufactured from thermoplastic ... -
Standard Specification for Steel or Aluminum Slotted Angle Crates
Abstract: This specification covers the material and fabrication of new reusable, slotted angle metal crates intended for use as containers for domestic and overseas shipment of lightweight airframe components and lightweight bulky ... -
Standard Specification for Wood-Cleated Shipping Boxes with Skidded, Load-Bearing Bases
Abstract: This specification covers the fabrication of wood-cleated shipping boxes with skidded. load-bearing bases designed for nonregulated domestic and overseas shipment of loads under a specified weight limit. Box performance ... -
Standard Test Method for Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle
Abstract: 5.1 This test method is a tool for quality assurance use. Given a pressure-sensitive label stock and a requirement in terms of the minimum or maximum peel adhesion value expected for this label stock, the data from the ... -
Standard Practice for Expedited Site Characterization of Vadose Zone and Groundwater Contamination at Hazardous Waste Contaminated Sites
Abstract: 4.1 The ESC Process—This practice describes a process for characterizing hazardous waste contaminated sites8, that provides cost-effective, timely, high-quality information derived primarily from judgement-based sampling ... -
Standard Test Method for Trace Benzene in Hydrocarbon Solvents by Capillary Gas Chromatography
Abstract: 4.1 This test method is similar to Test Method D4367 with the exception that capillary columns are used and intended for trace level of benzene in hydrocarbon solvents. The need for trace benzene analysis in hydrocarbon ... -
Standard Test Methods for Rough Handling of Unitized Loads and Large Shipping Cases and Crates
Abstract: 4.1 These test methods will allow the user to determine integrity and stability of the load as well as provide guidance to improve the design of the shipping container or the unit load where deficiencies are found. ... -
Standard Classification System and Basis for Specification for Extruded and Compression Molded Shapes Made from Polycarbonate (PC)
Abstract: This specification establishes the classification, requirements, and test methods for extruded and compression molded plates, rods, and tubular bars manufactured from polycarbonate or recycled plastics. This specification ... -
Standard Test Method for Tackiness of Finish on Leather
Abstract: 5.1 This test method is intended for use on any type of finished leather. 5.2 This test will give an indication of the tackiness of the finish on leather. -
Standard Test Method for Relative Resistance to Vented Water-Tree Growth in Solid Dielectric Insulating Materials
Abstract: 5.1 This is a laboratory test designed to simulate the growth of vented water-trees in the solid dielectric insulating material initiated by a sharp protrusion at the insulating and conductive interface under a wet environment ... -
Standard Guide for Selection of Methods for Assessing Sensitivity and Vulnerability of Groundwater in Intergranular Aquifers
Abstract: 4.1 Sensitivity and vulnerability methods can be applied to a variety of hydrogeologic settings, whether or not they contain specifically identified aquifers. However, some methods are best suited to assess groundwater ... -
Standard Specification for Castings, Nickel-Aluminum Ordered Alloy
Abstract: This specification covers nickel-aluminum ordered alloy castings intended for heat-resisting and elevated-temperature applications such as heat-resistant alloy structural members, containers, supports, hangers, spacers, ...