درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 481-500 of 39933
-
Standard Test Method for Measurement of Fuel System Icing Inhibitors (Ether Type) in Aviation Fuels
Abstract: 5.1 DiEGME is miscible with water and can be readily extracted from the fuel by contact with water during shipping and in storage. Methods are therefore needed to check the additive content in the fuel to ensure proper ... -
Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
Abstract: 5.1 The grab test procedure in this test method for the determination of breaking force and elongation is considered satisfactory for acceptance testing of commercial shipments of most woven or nonwoven textile fabrics, ... -
Standard Test Methods for Screening of Reactive Sulfides in Waste
Abstract: 5.1 These test methods are intended for use by waste treatment, storage, disposal, and remedial facilities in order to show the presence of potentially hazardous sulfide. 5.2 Method B: Gas Detector Tube—This proposed test ... -
Standard Test Method for Granule Adhesion to Mineral-Surfaced Roofing by Abrasion
Abstract: 3.1 This test method is used to determine the quality of adhesion of the granular surfacing to the coating asphalt in a sample of mineral-surfaced roofing. The results determine compliance with the applicable specification ... -
Standard Test Methods for Single-Filament Tire Bead Wire Made from Steel
Abstract: 5.1 The procedures for the determination of properties of single-filament bead wire made from steel are considered satisfactory for acceptance testing of commercial shipments of this product because the procedures are the ... -
Standard Test Method for Determination of Nitrilotriacetates in Detergents
Abstract: 3.1 This test method is suitable in research, development, and manufacturing control to monitor the level of NTA, a sequestering agent, in powder and liquid detergents. 3.2 Accurate determination of a sequestering agent ... -
Standard Test Method for Field Determination of Water (Moisture) Content of Soil by the Calcium Carbide Gas Pressure Tester
Abstract: 5.1 The water content of soil is used throughout geotechnical engineering practice, both in the laboratory and in the field. Results are sometimes needed within a short time period and in locations where it is not practical ... -
Standard Specification for Common Requirements for Bolting Intended for Use at Any Temperature from Cryogenic to the Creep Range
Abstract: This specification covers a group of common requirements that shall apply to carbon, alloy, and stainless steel fasteners or fastener materials, or both. These materials are intended for use at any temperature from cryogenic ... -
Standard Test Method for Blocking Resistance of Architectural Paints
Abstract: 5.1 Dry paint often comes in contact with itself especially in window and door areas and, depending on its hardness, the pressure, temperature, humidity, and duration of time the surfaces are in contact, sometimes sticks ... -
Standard Test Method for Shrinkage Factors of Cohesive Soils by the Water Submersion Method
Abstract: 5.1 The shrinkage limit can be used to evaluate the shrinkage potential, crack development potential, and swell potential of earthwork involving cohesive soils. 5.2 The shrinkage limit, along with the liquid limit and ... -
Standard Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blast Cleaning Abrasives
Abstract: 4.1 Abrasive media may contain ionic contamination naturally (for example, mineral abrasives), from manufacturing (quenching with contaminated water), transportation, storage or use (in the case of abrasive that is reused). ... -
Standard Specification for Automotive Spark-Ignition Engine Fuel
Abstract: This specification describes the various characteristics and requirements of automotive fuels for use over a wide range of operating conditions in ground vehicles equipped with spark-ignition engines. It provides for a ... -
Standard Test Methods for Coated and Laminated Fabrics for Architectural Use
Abstract: 5.1 The procedures in this standard can be used for acceptance testing of commercial shipments of coated and laminated fabrics for architectural use since these test methods have been used extensively in the trade for ... -
Standard Test Method for Heating Value of Gases in Natural Gas and Flare Gases Range by Stoichiometric Combustion
Abstract: 5.1 This test method provides an accurate and reliable procedure to measure the total heating value of a fuel gas, on a continuous basis, which is used for regulatory compliance, custody transfer, and process control. ... -
Standard Test Method for Unnotched Cantilever Beam Impact Resistance of Plastics
Abstract: 5.1 The pendulum-impact test indicates the energy to break standard test specimens of specified size under stipulated conditions of specimen mounting and pendulum velocity at impact. 5.2 The energy lost by the pendulum ... -
Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics
Abstract: 5.1 The test results represent the afterflame and afterglow times, in seconds, for a material under the conditions of the test. 5.2 The afterflame and afterglow times and other burning phenomena will vary with thickness. ... -
Standard Specification for Denatured Fuel Ethanol
Abstract: This specification covers nominally anhydrous denatured fuel ethanol intended for blending with unleaded or leaded gasolines for use as a spark-ignition automotive engine fuel. Denatured fuel ethanol shall conform to the ... -
Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater
Abstract: This specification covers the requirements for extruded (cast or blown) and compression-molded sheeting made from low-, medium-, and high-density polyethylenes and copolymers in specified thicknesses. Depending on the ... -
Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications
Abstract: This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications. If the primary melting is required it shall incorporate separate ...