درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 781-800 of 39933
-
Standard Specification for Steel Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
Abstract: This specification establishes the requirements for steel fiber reinforced concrete pipe (SFRCP) of internal diameters 12-48 in., to be used in the conveyance of sewage, industrial wastes, and storm water as well as the ... -
Standard Specification for Factory-Laminated Gypsum Panel Products
Abstract: This specification establishes the requirements for factory-laminated gypsum panel products designed for use either on walls, ceilings, or partitions as part of a sound control system, or as a gypsum stud or gypsum coreboard. ... -
Standard Guide for Measurement of the Rheological Properties of Hydraulic Cementitious Paste Using a Rotational Rheometer
Abstract: 4.1 Rheological properties determined using this guide include plastic viscosity and yield stress as defined by the Bingham model and apparent viscosity. 4.2 Rheological properties provide information about the workability ... -
Standard Test Method for Density and Void Content of Hardened Pervious Concrete
Abstract: 5.1 This test method is applicable to pervious concrete mixtures containing coarse aggregate with a nominal maximum size of 25 mm [1 in.] or smaller. 5.2 This test method applies to either core specimens or molded cylinders. ... -
Standard Guide for Comparing Seal or Sealant Behavior to Reference Photographs
Abstract: 4.1 This guide is intended to be used in evaluating sealant conditions that occur in service, along with other diagnostic techniques in failure analysis. These standard reference photographs have been selected and approved ... -
Standard Specification for Flexible Aerogel Insulation
Abstract: This specification covers the classification and performance of flexible aerogel thermal insulation. It indicates the mechanical, chemical, and property requirements of the flexible aerogel insulation, such as its thickness, ... -
Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
Abstract: This specification covers round, square, rectangular, and special shape electric-resistance-welded carbon and alloy steel mechanical tubing produced by hot- or cold-rolling. The types of tubing covered here are: Type 1a, ... -
Standard Specification for Preblended Dry Mortar Mix for Unit Masonry
Abstract: This specification covers unit masonry mortars whose material and design requirements are governed by a referenced ASTM document stated herein, but are preblended dry in a factory instead of produced from individual raw ... -
Standard Test Method for Density and Void Content of Freshly Mixed Pervious Concrete
Abstract: 5.1 This test method provides a procedure for determining the density and void content of freshly mixed pervious concrete. 5.2 This test method is applicable to pervious concrete mixtures containing coarse aggregate with ... -
Standard Specification for Joints for Concrete Box, Using Rubber Gaskets
Abstract: This specification covers flexible joints for concrete box sections, using rubber gaskets for leak resistant joints. The specification covers the design of joints and the requirements for rubber gaskets to be used. The ... -
Standard Test Method for Measurement of Roll Wave Optical Distortion in Heat-Treated Flat Glass
Abstract: 5.1 This test method is a procedure for determining the peak-to-valley depth and the wavelength of roll wave in flat glass and then calculating the optical distortion resulting from that roll wave. Peak-to-valley measurements ... -
Standard Specification for Fabrication Of Cellular Glass Pipe And Tubing Insulation
Abstract: This specification covers fabrication techniques for cellular glass block into billets to fabricate pipe and tubing insulation. The optimization of the thermal performance of installed cellular glass insulation systems is ... -
Standard Specification for Dry-Cast Concrete Facing Brick and Other Concrete Masonry Facing Units
Abstract: This specification covers solid, dry-cast, concrete facing brick intended for interior and exterior use in constructing structural and facing masonry components and are made from portland cement, water, and suitable mineral ... -
Standard Test Method for Determination of “Microwave Safe for Reheating” for Ceramicware
Abstract: 5.1 This test method is for evaluating ceramic products that are intended for reheating in a Consumer based microwave oven. It is not intended for evaluating products that will be used in commercial type microwaves. ... -
Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Flexural Testing (Stress Rupture) at Ambient Temperature
Abstract: 4.1 The service life of many advanced ceramic components is often limited by the subcritical growth (SCG) of cracks over time. In SCG conditions, small subcritical cracks in the ceramic may grow over time under stress in ... -
Standard Guide for Determining Blown Density of Pneumatically Applied Loose-Fill Mineral Fiber Thermal Insulation
Abstract: 4.1 Blown density is used to develop loose-fill coverage charts. Data for blown density vs thickness is used in the development of a variable blown density presentation for loose-fill insulation. 4.2 Thermal resistance ... -
Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel, and Alloy Steel
Abstract: This specification covers the general requirements for carbon steel wire rods and uncoated coarse round wire in coils or straightened and cut lengths. Chemical compositions are specified by ranges or limits for carbon and ...