درباره ما
Standard Test Methods for Rubber Deterioration—Dynamic Fatigue
ASTM D430-06
Organization:
ASTM - ASTM International
Year: 2025
Abstract: 4.1 Tests for dynamic fatigue are designed to simulate the continually repeated distortions received in service by many rubber articles, such as tires, belts, footwear, and molded goods. 4.1.1 These distortions may be produced by extension, compressive, and bending forces or combinations thereof. 4.1.2 The effect of the distortions is to weaken the rubber until surface cracking or rupture occurs. Where rubber is combined with other flexible materials such as fabric, the effect may be evidenced by separation at the interface between the materials, caused either by breaking of the rubber or failure of the adhesion or both. 4.2 These tests are, therefore, of the following two types: 4.2.1 Type I—Tests designed to produce separation of rubber-fabric combinations by controlled bending of the specimens. 4.2.2 Type II—Tests designed to produce cracking on the surface of rubber by either repeated bending or extension as may occur in service.
Collections
:
-
Statistics
Standard Test Methods for Rubber Deterioration—Dynamic Fatigue
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T19:23:57Z | |
| date available | 2025-09-30T19:23:57Z | |
| date copyright | 2025 | |
| date issued | 2025 | |
| identifier other | d0430-06r25.pdf | |
| identifier uri | http://yse.yabesh.ir/std;query=authoCA58ear3081D206861598F1EFDEC014A/handle/yse/343265 | |
| description abstract | 4.1 Tests for dynamic fatigue are designed to simulate the continually repeated distortions received in service by many rubber articles, such as tires, belts, footwear, and molded goods. 4.1.1 These distortions may be produced by extension, compressive, and bending forces or combinations thereof. 4.1.2 The effect of the distortions is to weaken the rubber until surface cracking or rupture occurs. Where rubber is combined with other flexible materials such as fabric, the effect may be evidenced by separation at the interface between the materials, caused either by breaking of the rubber or failure of the adhesion or both. 4.2 These tests are, therefore, of the following two types: 4.2.1 Type I—Tests designed to produce separation of rubber-fabric combinations by controlled bending of the specimens. 4.2.2 Type II—Tests designed to produce cracking on the surface of rubber by either repeated bending or extension as may occur in service. | |
| language | English | |
| title | Standard Test Methods for Rubber Deterioration—Dynamic Fatigue | en |
| title | ASTM D430-06 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2025 | |
| contenttype | fulltext | |
| scope | 1.1 These test methods cover testing procedures that estimate the ability of soft rubber materials to resist dynamic fatigue. No exact correlation between these test results and service is given or implied. This is due to the varied nature of service conditions. These test procedures do yield data that can be used for the comparative evaluation of rubber or composite rubber-fabric materials for their ability to resist dynamic fatigue. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/D0430-06R25 |