درباره ما
IEC - International Electrotechnical Commission: Recent submissions
Now showing items 761-780 of 9213
-
IEC 60122-1
Abstract: This part of IEC 60122 specifies the methods of test and general requirements for quartz crystal units of assessed quality using either capability approval or qualification approval procedures. -
IEC 62766-8
Abstract: This part of IEC 62766 defines three example profiles that may be adopted for implementation in suitable devices. -
IEC 60335-2-40 (REDLINE + STANDARD)
Abstract: This clause of Part 1 is replaced by the following. This part of IEC 60335 deals with the safety of electric heat pumps, including sanitary hot water heat pumps, air conditioners, and dehumidifiers incorporating motor-compressors ... -
IEC 60695-6-2
Abstract: This part of IEC 60695 provides a summary of commonly used test methods for the assessment of smoke obscuration. It presents a brief summary of static and dynamic test methods in common use, either as international standards ... -
IEC 62401
Abstract: This document applies to alarming radiation detection instruments that are pocket-sized, carried on the body and used to detect and indicate the presence and general magnitude of gamma radiation fields. Neutron detection ... -
IEC 63093-6
Abstract: This part of IEC 63093 specifies the dimensions that are of importance for mechanical interchangeability for a preferred range of ETD-cores made of ferrite and the essential dimensions of coil formers to be used with them, ... -
IEC 60335-2-4
Abstract: This clause of Part 1 is replaced by the following. This International Standard deals with the safety of stand alone electric spin extractors, and spin extractors incorporated in washing machines that have separate containers ... -
IEC 62386-216
Abstract: This part of IEC 62386 specifies a bus system for control by digital signals of electronic lighting equipment which is in line with the requirements of IEC 61347 (all parts), with the addition of DC supplies. This document ... -
IEC 60317-0-7
Abstract: This part of IEC 60317 establishes general requirements for fully insulated (FIW) zero-defect enamelled round copper wires. The nominal conductor diameter range is given in the relevant technical specification. -
-
IEC 60679-1
Abstract: This part of IEC 60679 specifies general requirements for piezoelectric, dielectric and electrostatic oscillators, including Dielectric Resonator Oscillators (DRO) and oscillators using FBAR (hereinafter referred to as ... -
IEC 61784-3
Abstract: This part of the IEC 61784-3 series explains some common principles that can be used in the transmission of safety-relevant messages among participants within a distributed network which use fieldbus technology in accordance ... -
IEC 62928
Abstract: This document applies to onboard lithium-ion traction batteries for railway applications. This document specifies the design, operation parameters, safety recommendations, data exchange, routine and type tests, as well as ... -
IEC 61190-1-3
Abstract: This part of IEC 61190 prescribes the requirements and test methods for electronic grade solder alloys, for fluxed and non-fluxed bar, ribbon, powder solders and solder paste, for electronic soldering applications and for ... -
IEC 61238-1-2
Abstract: This part of IEC 61238 applies to insulation piercing connectors for power cables for rated voltages up to 1 kV (Um = 1,2 kV), for example according to IEC 60502-1 or other buried cables and cables installed in buildings, ... -
IEC 62714-1
Abstract: This part of IEC 62714 specifies general requirements and the architecture of automation markup language (AML) for the modelling of engineering information, which is exchanged between engineering tools for industrial ... -
IEC TR 63114
Abstract: This Technical Report describes the general principle and technical details of the reverse bend test method used for evaluating the ductility of electrical steel strip and sheet. This test method is applicable to Epstein ... -
IEC PAS 63151
Abstract: This Publicly Available Specification (PAS) specifies protocols and test procedures for the reproducible measurement of the peak spatial-average specific absorption rate (psSAR) induced inside a simplified model of the ... -
IEC 62631-2-1
Abstract: This part of IEC 62631 describes test methods for the determination of permittivity and dissipation factor properties of solid insulating materials (AC methods from 0,1 Hz up to 10 MHz). NOTE This part of the standard ... -
IEC 60721-2-4 (REDLINE + STANDARD)
Abstract: This part of IEC 60721 presents a broad division into types of solar radiation areas. It is intended to be used as part of the background material when selecting appropriate severities of solar radiation for product ...