Defence Standards: Recent submissions

Now showing items 741-760 of 43216

    • NATO STANAG 1278 

      Type: standard
      Source: NATO - North Atlantic Treaty Organization:;2005
      Organization : NATO - North Atlantic Treaty Organization
      Abstract: The aim of this agreement is to establish minimum standard requirements of coefficient of friction in order to reduce the possibility of aircraft sliding on flight decks.

    • MIL-S-70692 

      Type: standard
      Source: ARMY - AR - US Army Research Devlp & Engr Command, Armament Research Devlp & Engr Center:;1988
      Organization : ARMY - AR - US Army Research Devlp & Engr Command, Armament Research Devlp & Engr Center
      Abstract: This specification covers the requirements and quality assurance provisions for the manufacture and acceptance of one type of Sym-di-beta-naphthylparaphenylenediamine (see 6.1). Intended Use: The ...
      Subject(s) : Antioxidant , Projectile , Propellant ,

    • DODD 7720.22 

      Type: standard
      Source: DODD - DoD Directives Service:;1979
      Organization : DODD - DoD Directives Service

    • NASA-LLIS-1475 

      Type: standard
      Source: NASA - National Aeronautics and Space Administration (NASA):;2003
      Organization : NASA - National Aeronautics and Space Administration (NASA)
      Abstract: Abstract:
      The "Investigation Organizer" management and modeling tool was the primary investigation management tool for the Columbia accident investigation; however, acceptance of the tool was not ...
      Subject(s) : Accident Investigation , Administration/Organization , Computers , Information Technology/Systems , NASA Standards , Policy & Planning , Research & Development , Safety & Mission Assurance ,

    • NASA-LLIS-2158 

      Type: standard
      Source: NASA - National Aeronautics and Space Administration (NASA):;2011
      Organization : NASA - National Aeronautics and Space Administration (NASA)
      Abstract: When a project plans to reuse existing metrology software for a new application, a thorough independent review of the software and its new interfaces should be conducted.
      Subject(s) : Engineering Design (Phase C/D) , Engineering Design (Phase C/D).Software Engineering , Missions and Systems Requirements Definition. , Missions and Systems Requirements Definition.Configuration control and data management , Program Management. , Program Management.Configuration and data management , Systems Engineering and Analysis. , Systems Engineering and Analysis.Engineering design and project processes and standards , Systems Engineering and Analysis.Planning of requirements verification processes ,

    • DSCC-VID-V62/05603 

      Type: standard
      Source: DLA - CC - DLA Land and Maritime:;2005
      Organization : DLA - CC - DLA Land and Maritime
      Abstract: This drawing documents the general requirements of a high performance logarithmic amplifier microcircuit, with an operating temperature range of −55°C to +125°C.

    • A-A-59753 

      Type: standard
      Source: AIR FORCE - 69 - Air Force Packaging Technology and Engineering Facility (AFPTEF):;2004
      Organization : AIR FORCE - 69 - Air Force Packaging Technology and Engineering Facility (AFPTEF)
      Abstract: This Commercial Item Description (CID) describes the minimum requirements for a Function Generator. The equipment, as described in this CID, shall have a minimum frequency range of 0.1 Hz to 4 MHz. This CID is meant as a ...

    • SMD-5962-84129 REV F 

      Type: standard
      Source: DLA - CC - DLA Land and Maritime:;2009
      Organization : DLA - CC - DLA Land and Maritime
      Abstract: This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A.Intended Use: Microcircuits conforming to this drawing ...

    • A-A-51175B VALID NOTICE 1 

      Type: standard
      Source: DLA - GS6 - DLA Aviation - Richmond:;2013
      Organization : DLA - GS6 - DLA Aviation - Richmond

    • SMD-5962-90965 REV H 

      Type: standard
      Source: DLA - CC - DLA Land and Maritime:;2011
      Organization : DLA - CC - DLA Land and Maritime
      Abstract: This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are ...

    • MIL-C-572G (1) 

      Type: standard
      Source: ARMY - AR - US Army Research Devlp & Engr Command, Armament Research Devlp & Engr Center:;1972
      Organization : ARMY - AR - US Army Research Devlp & Engr Command, Armament Research Devlp & Engr Center

    • MIL-P-40061B VALID NOTICE 1 

      Type: standard
      Source: ARMY - IH - Institute of Heraldry:;1992
      Organization : ARMY - IH - Institute of Heraldry

    • MIL-DTL-11132/13F 

      Type: standard
      Source: ARMY - IH - Institute of Heraldry:;2013
      Organization : ARMY - IH - Institute of Heraldry

    • MIL-STD-1320/188 

      Type: standard
      Source: NAVY - OS - Naval Surface Warfare Center (NSWCIHEODTD):;1978
      Organization : NAVY - OS - Naval Surface Warfare Center (NSWCIHEODTD)

    • A-A-58000 VALID NOTICE 1 

      Type: standard
      Source: AIR FORCE - 69 - Air Force Packaging Technology and Engineering Facility (AFPTEF):;2012
      Organization : AIR FORCE - 69 - Air Force Packaging Technology and Engineering Facility (AFPTEF)
      Abstract: This Commercial Item Description (CID), describes a 3000 and 6000 gallon horizontal cryogenic storage tank capable of storing and delivering liquid oxygen or liquid nitrogen.
      The storage tanks shall be of the following ...

    • MSFC-SPEC-1826 REV A CHG NOTICE 5 

      Type: standard
      Source: MSFC - NASA - MSFC - Marshall Space Flight Center:;1995
      Organization : MSFC - NASA - MSFC - Marshall Space Flight Center

    • MIL-HDBK-271 -102 

      Type: standard
      Source: DLA - IS - DLA Troop Support - Industrial Hardware Items of Supply Standardization Code:;1984
      Organization : DLA - IS - DLA Troop Support - Industrial Hardware Items of Supply Standardization Code
      Abstract: This handbook covers the installation and removal methods for 120° (MS14218) rivets.

    • DODD 7000.14-R VOL 3 CHAP 10 

      Type: standard
      Source: DODD - DoD Directives Service:;2012
      Organization : DODD - DoD Directives Service
      Abstract: Purpose
      This chapter implements within the Department of Defense (DoD) certain provisions of chapter 15 of title 31, United States Code (U.S.C.), relating to expired and closed accounts.

    • SMD-5962-89689 REV D 

      Type: standard
      Source: DLA - CC - DLA Land and Maritime:;2010
      Organization : DLA - CC - DLA Land and Maritime
      Abstract: This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are ...

    • GSFC-S-311-384 

      Type: standard
      Source: GSFC - NASA - GSFC - Robert H. Goddard Space Flight Center:;1985
      Organization : GSFC - NASA - GSFC - Robert H. Goddard Space Flight Center