درباره ما
JSA - Japanese Standards Association
Browse by
Recent Submissions
-
JSA JIS C 3662-5
Abstract: This Standard specifies polyvinyl chloride insulated flexible cables (cords) of rated voltages up to and including 300/500 V. All cables comply with the appropriate requirements given in JIS C 3662-1, and each individual ... -
JSA JIS H 8453
Abstract: This Standard specifies the method for determining the thermal conductivities of thermal barrier coatings that consist of metallic bond coats and ceramic top coats, in a direction normal to the coating surface, at room ... -
JSA JIS C 8156
Abstract: This Standard specifies the safety and interchangeability requirements, together with the test methods and conditions required to show compliance of LED-lamps with integrated means for stable operation (hereafter referred ... -
JSA JIS K 0117
Abstract: This Japanese Industrial Standard specifies the general rules applicable to the qualitative analysis and quantitative analysis of inorganic and organic substances using infrared spectrophotometer 1). Note 1) In a broad ... -
JSA JIS Z 2343-1
Abstract: This Standard specifies a method of penetrant testing used to detect discontinuities, e.g. cracks, laps, folds, porosity and incomplete fusion, which are open to the surface of the materials and products in manufacturing ... -
JSA JIS Z 3119
Abstract: This Standard specifies the methods of measurement for ferrite content in austenitic and austenitic-ferritic stainless steel deposited metals ,by means of microstructure, constitutional diagram and magnetic ... -
JSA JIS B 1200
Abstract: This Standard specifies characteristics for hexagon weld nuts with flange, with sizes M5 to M16 (coarse thread) or D = 8 mm to 16 mm (fine pitch thread), of product grade A (hereafter referred to as nuts). Nuts conforming ... -
JSA JIS K 6261-3
Abstract: This Standard specifies a static procedure, known as the Gehman test, for determining the relative stiffness characteristics of vulcanized or thermoplastic rubbers over a temperature range from room temperature to approximately ... -
JSA JIS Z 2320-2
Abstract: This Standard specifies the significant properties of magnetic particle testing products (including detection media, magnetic particle, carrier liquid, contrast aid paints) and the methods for checking their properties. ... -
JSA JIS G 1323-5
Abstract: This Japanese Industrial Standard specifies the method for determination of iron content in chromium metal. -
JSA JIS A 1159
Abstract: This Japanese Industrial Standard specifies the J -ring flow test method intended for high-fluidity concrete with maximum coarse aggregate size of 40 mm or under. -
-
JSA JIS B 7724
Abstract: This Standard specifies methods of direct and indirect verification of testing machines used for determining Brinell hardness in accordance with JIS Z 2243. This Standard is applicable to both fixed location and portable ... -
JSA JIS S 3201
Abstract: This Japanese Industrial Standard specifies the testing methods of filtration flow rate, minimum dynamic water pressure, recovery, removal performance and filtering capability for the water purifiers mainly used in the ... -
JSA JIS B 1111
Abstract: This Standard specifies the characteristics of cross recessed head screws. If, in special cases, specifications other than those given in this Standard are required, they can be selected from existing Japanese Industrial ... -
JSA JIS Z 3147
Abstract: This Japanese Industrial Standard specifies the method of high-speed rotating bar bending fatigue testing at room temperature and at a frequency of over 5 000 cycles/min up to and including 8 000 cycles/min (hereafter ... -
JSA JIS G 3521
Abstract: This standard specifies hard drwn steel wires that are applied mainly to springs for static duty applications (hereafter referred to as wires). NOTE: The International Standards corresponding to this Standard and the symbol ... -
JSA JIS G 1323-1
Abstract: This Japanese Industrial Standard specifies the method for determination of carbon content in chromium metal. -
JSA JIS B 8210
Abstract: Tis Standardcifies requments for full borafety valves with a set pressure of 0.1 mpA (guage pressure)1) and above and with a throat diameter of 7 mm and above, and curtain area restricted safety valves with a valves seat ... -
JSA JIS G 3460
Abstract: This Standard specifies the steel pipes (hereafter referred to as pipes) used for piping at extremely low temperatures of freezing point or under. This Standard is generally applicable to pipes of outside diameter 10.5 mm ...