درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 1461-1480 of 39933
-
Standard Test Method for Quantitative Determination of Phases in Portland Cement Clinker by Microscopical Point-Count Procedure
Abstract: 5.1 This test method provides a relatively simple and reliable microscopical means of measuring the phase abundance of portland cement clinker (Note 1). Microscopical point counting provides a direct measure of the clinker ... -
Standard Test Method for Determination of Low Mass Density/Fractions of Uranium in Oils, Organic Liquids, and Pellets by X-ray Fluorescence
Abstract: 5.1 This test method is applicable to organic solutions containing uranium at 20 μg/mL to 2000 μg/mL presented to the spectrometer for the solution techniques or pellets containing uranium at 200 μg/g to 50 000 μg/g using ... -
Standard Guide for Use of Joint Sealants with Exterior Insulation and Finish Systems (EIFS)
Abstract: 4.1 The intent of this guide is to provide information and guidelines for consideration by the designer or applicator of joint seals in, or adjacent to, EIFS. Refer to Specification E2568 for additional information pertaining ... -
Standard Test Method for Flowability and Bearing Area of Chemical-Resistant Polymer Machinery Grouts
Abstract: 5.1 Chemical-resistant polymer machinery grouts are used to provide precision support for machinery or equipment. Note 2: The machinery or equipment or support bases or plates, or combination thereof, are positioned to the ... -
Standard Test Method for Compressive Strength of Masonry Prisms
Abstract: 4.1 This test method provides a means of verifying that masonry materials used in construction result in masonry that meets the specified compressive strength (Note 1). Note 1: A prism is an assembly of components used to ... -
Standard Test Method for Hydrostatic Pressure Resistance of a Liquid-Applied Waterproofing Membrane
Abstract: 5.1 This test method is used as a screening tool to determine the hydrostatic pressure to which a liquid-applied waterproofing membrane may be subjected without failing when stretched over a crack in the substrate. This ... -
Standard Test Method for Gamma Energy Emission from Fission and Decay Products in Uranium Hexafluoride and Uranyl Nitrate Solution
Abstract: 5.1 Specific gamma-ray emitting radionuclides in UF6 are identified and quantified using a high-resolution gamma-ray energy analysis system, which includes a high-resolution germanium detector. This test method shall be ... -
Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
Abstract: 4.1 The procedure described in this test method is intended to determine the effects of freezing and thawing on SRW and related units in the presence of potable tap water or saline solution. 4.2 The procedure is not ... -
Standard Specification for Fiber-Reinforced Gypsum Panel
Abstract: This specification covers fiber-reinforced gypsum panel. The physical properties, dimensions and tolerances, and edges of interior fiber-reinforced gypsum panels, water-resistant fiber-reinforced gypsum backing panels, ... -
Standard Practice for Preparation of Oils and Oily Waste Samples by High-Pressure, High-Temperature Digestion for Trace Element Determinations
Abstract: 5.1 This practice is useful for preparation of difficult-to-digest, primarily oils and oily wastes, specimens for trace element determinations of up to 28 elements by atomic absorption or plasma emission techniques. Specimen ... -
Standard Guide for Installation of Walk-Through Metal Detectors
Abstract: 4.1 This guide is intended for use by the designers, the evaluators, and the users of WTMDs that are installed to screen persons entering or leaving a controlled access or other designated area. This guide is not meant to ... -
Standard Guide for Selection, Design, and Installation of Dimension Stone Attachment Systems
Abstract: 4.1 This guide is intended to be used by architects, engineers, and contractors who either design or install exterior stone cladding for architectural structures. 4.2 This guide is an industry standard for engineering ... -
Standard Test Method for Vickers Indentation Hardness of Advanced Ceramics
Abstract: 5.1 For advanced ceramics, Vickers indenters are used to create indentations whose surface-projected diagonals are measured with optical microscopes. The Vickers indenter creates a square impression from which two ... -
Standard Guide for Preparing and Interpreting Precision and Bias Statements in Test Method Standards Used in the Nuclear Industry
Abstract: 4.1 To describe the performance of a standard test method, precision and bias statements are required.5 Committee E11 on Probability and Statistics has published standards addressing these terms and the preparation of ... -
Standard Specification for Precast Concrete Septic Tanks
Abstract: This specification covers monolithicor sectional precast concrete septic tanks. The following materials shall be used for manufacturing concrete septic tank: cement, aggregates, water, admixtures, steel reinforcement, ... -
Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel
Abstract: This specification covers coated glass mat water-resistant gypsum backing panel designed for use on ceilings and walls in bath and shower areas as a base for the application of ceramic or plastic tile. Coated glass mat ... -
Standard Test Method for Compressive Strength of Architectural Cast Stone
Abstract: 4.1 This test method is to be used in determining the compressive strength of cast stone. Compressive strength is one measure of resistance of cast stone to weathering and structural stress. -
Standard Specification for Laminated Architectural Flat Glass
Abstract: This specification covers the quality requirements for cut sizes of flat laminated glass consisting of two or more lites of glass bonded with an interlayer material for use in building glazing. Depending on the number, ...