درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 21-40 of 36496
-
Standard Specification for Tin Mill Products, Black Plate, Double Reduced
Abstract: This specification covers doubled-reduced black plate tin mill products produced from low-carbon cold-reduced steel, furnished in coils and cut sizes, for use predominantly in the manufacture of containers. The product, ... -
Standard Specification for Aluminum-Pigmented Asphalt Roof Coatings, Nonfibered, and Fibered without Asbestos
Abstract: This specification covers three types of aluminum-pigmented asphalt roof coatings suitable for application to roofing or masonry surfaces by brush or spray. Type I is nonfibered, Type II is fibered with asbestos, and Type ... -
Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
Abstract: 5.1 Coatings attached to substrates are subjected to damaging impacts during the manufacture of articles and their use in service. In its use over many years, this test method for impact resistance has been found to be ... -
Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
Abstract: 5.1 Many important properties of crosslinked ethylene plastics vary with the gel content. Hence, determination of the gel content provides a means of both controlling the process and rating the quality of finished products. ... -
Standard Test Method for Block Resistance of Organic Coatings on Wood Panel Substrates
Abstract: 4.1 Coated wood panel products must be stacked face to face or face to back during warehousing, packaging, and transportation without the coated finish sticking (blocking) and becoming damaged. This test method describes ... -
Standard Practices for Sampling Particulate Ion-Exchange Materials
Abstract: 5.1 This practice will be used most frequently to sample materials as received from the manufacturer in the original shipping container and prior to any resin-conditioning procedure. Since certain ion-exchange materials ... -
Standard Specification for Crosslinkable Ethylene Plastics
Abstract: This specification covers a general classification system for crosslinkable ethylene plastics compounds. Two types of compounds are covered, namely, mechanical types in which mechanical strength properties are of prime ... -
Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)
Abstract: 5.1 This test method is considered satisfactory for acceptance testing of commercial shipments since current estimates of between-laboratory precision are acceptable, and the test method is used extensively in the trade ... -
Standard Test Method for Smoke Density in Flue Gases from Burning Distillate Fuels
Abstract: 5.1 This test method provides a means of controlling smoke production in home heating equipment to an acceptable level. Excessive smoke density adversely affects efficiency by heat-exchanger fouling. 5.2 The range of smoke ... -
Standard Test Method for Evaluation of Wetting Agents by the Skein Test
Abstract: This test method covers the determination of the efficiency of ordinary commercial wetting agents using the skein test. It is applicable under limited and controlled conditions, but does not necessarily yield information ... -
Standard Test Method for Thermal Endurance of Flexible Sheet Materials Used for Electrical Insulation by the Curved Electrode Method
Abstract: 5.1 A major factor affecting the life of insulating materials is thermal degradation. Other factors, such as moisture and vibration, are able to cause failures after the material has been weakened by thermal degradation. ... -
Standard Test Method for Print Resistance of Lacquers
Abstract: 4.1 An unsatisfactory appearance can result from pressure deformation of a film inherently too soft or containing residual solvent. This test method is primarily used to evaluate the resistance of a lacquer finish to ... -
Standard Test Methods for Sampling and Testing Untreated Mica Paper Used for Electrical Insulation
Abstract: 7.1 Accurate determination of thickness is important for identification purposes. Thickness is related to weight and must be known in order to calculate apparent density and the dielectric strength. 7.2 Thickness variation ... -
Standard Test Methods for Determination of Tin Coating Weights for Electrolytic Tin Plate
Abstract: 20.1 This test method covers determination of the total tin in the sample tested and does not apportion the tin to one or the other side of the test specimen. The calculations appearing in Section 27 assume uniform ... -
Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing
Abstract: This specification covers emulsified asphalt suitable for use as a protective coating for built-up roofs and other exposed surfaces with specified inclines. The emulsified asphalts are grouped into three types, as follows: ... -
Standard Specification for Asphalt-Base Emulsions for Use as Protective Coatings for Metal
Abstract: This specification establishes the manufacture, testing, and performance requirements of two types of asphalt-based emulsions for use in a relatively thick film as a protective coating for metal surfaces. Type I are ... -
Standard Guide for pH of Aqueous Solutions of Soaps and Detergents
Abstract: This guide details the standard procedures for the preparation of aqueous solutions of soaps and detergents and the determination of their pH. The required reagent for this procedure is distilled water or its equivalent, ... -
Standard Test Method for Dissipation Factor and Permittivity (Dielectric Constant) of Mica
Abstract: 4.1 The dissipation factor of natural muscovite mica, as determined by this test method, is of practical importance as a measure of the electrical energy lost as heat in the mica serving as the dielectric substance of ... -
Standard Test Method for Stiffness Properties of Plastics as a Function of Temperature by Means of a Torsion Test
Abstract: 4.1 The property measured by this test is the apparent modulus of rigidity, G, sometimes called the apparent shear modulus of elasticity. It is important to note that this property is not the same as the modulus of elasticity, ...