درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 2201-2220 of 39933
-
Standard Test Method for Length and Length Distribution of Manufactured Staple Fibers (Single-Fiber Test)
Abstract: 5.1 This test method is used for research, development, quality control, product specifications, and may be used for acceptance testing of commercial shipments of textile fibers. However, caution is advised since information ... -
Standard Practice for Determining Cracking Susceptibility of Metals Exposed Under Stress to a Hot Salt Environment
Abstract: 5.1 The hot salt test as applied to metals is utilized as a secondary design consideration indicator, as cracking has been shown to occur in laboratory tests simulating possible service conditions. Although limited evidence ... -
Standard Practice for Conducting Exposures to Daylight Filtered Through Glass
Abstract: 4.1 Since solar radiation, air temperature, relative humidity, and the amount and kind of atmospheric contaminants vary continuously, results from exposures based on elapsed time will sometimes differ. The variations in ... -
Standard Test Methods for Cathodic Disbonding of Coated Steel
Abstract: 4.1 Breaks or holidays in a coating applied over steel exposes the substrate to a potential corrosion cell. When the steel is subjected to cathodic protection by the polarization of the steel via sacrificial anodes or ... -
Standard Test Method for Assessing Carpet Wetness after Cleaning with a Wet Extraction Cleaning System
Abstract: 4.1 This test method will provide an indication of the carpet wetness after cleaning with a given wet extraction cleaning system. The carpet wetness measured in the laboratory test may not be the same as in home cleaning ... -
Standard Guide for Ceiling Suspended and Wall Mounted Basketball Backstops
Abstract: 4.1 This guide is to aid the specifier, designer, owner/operator, and others, when determining the best practices for ceiling suspended and wall mounted backstops. 4.2 This guide can be helpful in most applications where ... -
Standard Guide for Credential-Based A2X Broadcast Security
Abstract: 5.1 This standard provides guidance for using cryptographic credentials to secure localized A2X-Direct communications as defined in 5.3. It is not intended to specify or infer the security requirements for any one A2X ... -
Standard Test Method for Performance of Commercial Range Ovens
Abstract: 5.1 Thermostat Calibration—This test is conducted to ensure that all test results are determined at the same bulk oven cavity air temperature. 5.1.1 The results of the following tests can be used by an operator to select ... -
Standard Specification for Hydrogel Projectile Launchers
Abstract: 4.1 This specification establishes performance requirements and test methods for HP launchers. -
Standard Test Method for Fire Testing of Vandalized Upholstered Furniture
Abstract: 5.1 This test method provides a means to measure a variety of fire-test-response characteristics resulting from burning a specimen of upholstered furniture, both as manufactured and after vandalization to expose the padding. ... -
Standard Guide for Testing Advancing Skimming Systems
Abstract: 4.1 Current industry practice has been to claim the capacity of a skimmer based on the throughput of the discharge pump (which is typically measured using water as a test fluid) and then applying a de-rating factor to ... -
Standard Specification for Rope-Lay-Stranded Copper Conductors Having Bunch-Stranded Members, for Electrical Conductors
Abstract: This specification covers bare rope-lay-stranded conductors having bunch-stranded members from round copper wires, either uncoated or coated with tin, lead, or lead-alloy for use in electrical conductors. Rope-lay-stranded ... -
Standard Test Method for Adhesion of Mineral Aggregate to Hot Bitumen
Abstract: 5.1 The quantities of mineral aggregate adhered to the surface of a roof vary with the characteristics and total amount of the aggregate. Mineral aggregate shields bituminous membranes from solar radiation. Unadhered mineral ... -
Standard Practice for Maintaining Oxidative Capacity of Test Solutions for Degradation Screening of Non-Absorbable Polymers
Abstract: 4.1 This standard practice summarizes a method to maintain the oxidative capacity of test solutions, in line with the recommendations of ISO 10993-13. The approach outlined in this standard practice is applicable for ongoing ... -
Standard Practice for Heat Fusion Joining of Polypropylene (PP) Pipe and Fittings
Abstract: 5.1 The procedures described in this practice are intended for joining of polypropylene (PP) pipe and fittings using suitable equipment and appropriate environmental control procedures. When properly implemented, strong ... -
Standard Practice for General Guidance on Damage Tolerance Evaluation of Normal Category Aeroplane
Abstract: 4.1 This practice provides general guidance for damage tolerance evaluation that can be used in conjunction with Specification F3115/F3115M to demonstrate adequate structural durability of metallic structures. Users of ... -
Standard Practice for Pole Vault Use Areas
Abstract: 4.1 This guide establishes the safety, performance, and maintenance recommendations pertaining to indoor/outdoor, public, and private-use pole vault facilities and any elements included therein that are intended to be used ...