درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 3201-3220 of 39933
-
Standard Test Method for Hiding Power of Architectural Paints Applied by Roller
Abstract: 5.1 Laboratory hiding power measurements of architectural coatings generally employ blade-type applicators that lay down films of highly uniform thickness. But practical applicators, such as rollers, pads, and brushes, ... -
Standard Test Method for Ozone in the Atmosphere: Continuous Measurement by Ethylene Chemiluminescence
Abstract: 4.1 Air quality standards for ozone have been promulgated by government authorities to protect the health and welfare of the public. Though ozone itself is a toxic material, it is often complex organic compounds that cause ... -
Standard Specification for High Purity p-Xylene
Abstract: This specification establishes the requirements for p-Xylene. Sampled specimens shall conform to the following physical and chemical properties: minimum purity; maximum m-Xylene content; maximum o-Xylene content; maximum ... -
Standard Test Method for Amylaceous Matter in Adhesives
Abstract: 5.1 This test method is used to determine if a melamine resin, a phenol, or a resorcinol adhesive contains any starch-like filler, the presence of which could affect water resistance or strength, or both. -
Standard Test Methods for Measurement of Hydraulic Conductivity of Saturated Porous Materials Using a Flexible Wall Permeameter
Abstract: 4.1 These test methods apply to one-dimensional, laminar flow of water within porous materials such as soil and rock. 4.2 The hydraulic conductivity of porous materials generally decreases with an increasing amount of air ... -
Standard Test Methods for Gross Leakage of Liquids from Containers with Threaded or Lug-Style Closures
Abstract: 5.1 These test methods are qualitative and used to indicate the integrity of the container and closure system in the distribution environment. 5.2 These test methods measure the ability of the container and closure system ... -
Standard Test Method for Determining the Performance of a Cup Anemometer or Propeller Anemometer
Abstract: 5.1 This test method provides a standard for comparison of rotating type anemometers, specifically cup anemometers and propeller anemometers, of different types. Specifications by regulatory agencies (4-7) and industrial ... -
Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists
Abstract: This specification gives procedures for establishing, monitoring, and reevaluating structural capacities of prefabricated wood I-joists. Capacities considered are shear, moment, and stiffness. Procedures for establishing ... -
Standard Test Method for Measurement of Fuel System Icing Inhibitors (Ether Type) in Aviation Fuels
Abstract: 5.1 DiEGME is miscible with water and can be readily extracted from the fuel by contact with water during shipping and in storage. Methods are therefore needed to check the additive content in the fuel to ensure proper ... -
Standard Test Method for Determination of Linear Low Density Polyethylene (LLDPE) Composition by Carbon-13 Nuclear Magnetic Resonance
Abstract: 5.1 Performance properties are dependent on the number and type of short chain branches. This test method permits measurement of these branches for ethylene copolymers with propylene, butene-1, hexene-1, octene-1, and ... -
Standard Practice for Differential Dyeing Behavior of Cotton
Abstract: 5.1 This practice is not recommended for acceptance testing because the information obtained is qualitative rather than quantitative in nature. 5.2 The response of fibers to the dye mixture is indicative of the uniformity ... -
Standard Test Method for Total Sulfur in Coal and Coke Combustion Residues Using a High-Temperature Tube Furnace Combustion Method with Infrared Absorption
Abstract: 5.1 The sulfur mass fraction of the ash derived from coal or coke can be calculated to sulfur trioxide mass fraction. This information can be used in combination with results from the determination of major, minor and or ... -
Standard Practice for Recovery of Replicable Viruses from Municipal Wastewater Sludges
Abstract: 4.1 Although many laboratories are presently isolating viruses from sludge, a valid comparison of data generated has not been possible because of the lack of a standard test method(s). -
Standard Test Method for Determination of Water Content of Soil By Direct Heating
Abstract: 5.1 The water content of a soil is used throughout professional practice both in the laboratory and in the field. The use of Test Methods D2216 for water content determination can be time consuming and there are occasions ... -
Standard Test Method for Comparison of the Brush Drag of Latex Paints
Abstract: 5.1 As the brush drag of a paint increases, any natural tendency on the part of the painter to overspread the paint is reduced. When all other factors are held constant, increased brush drag will result in greater film ... -
Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum-Tungsten
Abstract: This specification covers chromium-molybdenum-tungsten alloy steel plates intended primarily for welded boilers and pressure vessels designed for elevated temperature service. The plates shall be available in three grades, ... -
Standard Test Method for Density of In-place Soil and Rock Materials by the Sand Replacement Method in a Test Pit
Abstract: 5.1 This test method can be used to determine the in-place density and water content of compacted soil and rock materials placed during construction of earth embankments, road fills, and structural backfill. For construction ... -
Standard Test Method for Determination of Organic Chloride Content in Crude Oil
Abstract: 5.1 Organic chlorides do not occur naturally in crude oil. When present, they result from contamination in some manner, such as disposal of chlorinated solvent used in many dewaxing pipeline or other equipment operations. ... -
Standard Test Method for Water in Crude Oils by Coulometric Karl Fischer Titration
Abstract: 5.1 The accurate analysis of a crude oil sample to determine the water content is important in the refining, purchase, sale, or transfer of crude oils. -
Standard Test Method for Density of Solid Pitch (Helium Pycnometer Method)
Abstract: 5.1 This test method is useful in characterizing pitches as one element in establishing uniformity of shipments and sources of supply. With this method, the density is determined to two decimal places, which is sufficient ...