Show simple item record

CONNECTORS, ELECTRICAL, RECTANGULAR, HIGH DENSITY, LOBE KEYED, NANOMINIATURE, GENERAL REQUIREMENTS FOR

contributor authorDLA - CC - DLA Land and Maritime
date accessioned2017-09-04T16:19:25Z
date available2017-09-04T16:19:25Z
date copyright04/22/1996
date issued1996
identifier otherTHYZDAAAAAAAAAAA.pdf
identifier urihttps://yse.yabesh.ir/std/handle/yse/82815
description abstractThis drawing outlines the general requirements for families of high density, high performance electrical connectors, intended for general usage where space and weight are of primary concern. These connectors utilize attached harness, printed circuit through hole or printed circuit surface mount termination means, and include features for polarization or keying. Interface contact patterns for these connectors is on a 0.635 millimeter (0.025 inch) spacing grid.
Connectors conforming to this general requirements drawing must be capable of operating in the following environments:
a. Temperature from −65°C to +125°C with temperature cycling.
b. Altitudes from sea level to 21,336 meters (70,000 ft).
c. Moisture conditions up to 100{}elative humidity.
d. Dust and fine sand atmosphere.
e. Salt laden atmosphere.
f. Vibration conditions to 20 g's.
g. Shock conditions up to 100 g's.
The complete PIN shall be as specified on the individual requirements drawing and constructed using the following format, (also see 1.2.9): CHART
Insulators shall be fabricated utilizing one of the following plastic materials:
a. Thermoplastic, type GST-40F per MIL-M-24519.
b. Thermosetting plastic, type GDI-30F per MIL-M-14.
c. Thermoplastic, type GLCP-30F per MIL-M-24519.
Connectors shall be terminated using the following techniques:
a. Attached solid uninsulated wire harness.
b. Attached stranded insulated wire harness.
c. Printed circuit vertical through hole mount.
d. Printed circuit right angle through hole mount.
e. Printed circuit vertical surface mount.
f. Printed circuit right angle surface mount.
g. Ribbon cable.
h. Flex circuitry.
The PIN shall include 5 digits to identify the total number of contacts. The first three digits will identify the number of signal contacts and the following two digits identifying the number of special contacts (shielded, power, etc.). CHART
The PIN will utilize a double character (01 or 02) to identify single or double row connectors. Each individual requirement drawing will provide a figure which will identify available configuration types and an associated code letter to be included in the PIN.
Contact seating will be identified in the last character position of the PIN as follows:
         S  - Connectors are seated to prevent entry of cleaning fluids, or conformal coatings               into the contact area from the termination side of the connector.


Shell material is specified in the last character or the PIN. The available shell options and associated code letters to be used in the PIN are as follows:
1. Metal shell, corrosion resistant steel.
2. Metal shell, aluminum.
3. Plastic
Mounting hardware is specified in DESC drawing 94045.
Backshell hardware is specified in DESC drawing 94046.
Ancillary hardware, when specified on an individual requirements drawing, shall be specified in the following format: CHART
Intended Use: These connectors are designed for printed wiring board to printed wiring board, printed wiring board to cable, cable to panel, or cable to cable interconnections of miniaturized equipment sub-assemblies with low power requirements.
languageEnglish
titleDSCC-DWG-94031num
titleCONNECTORS, ELECTRICAL, RECTANGULAR, HIGH DENSITY, LOBE KEYED, NANOMINIATURE, GENERAL REQUIREMENTS FORen
typestandard
page15
statusRevised
treeDLA - CC - DLA Land and Maritime:;1996
contenttypefulltext


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record