Search
Now showing items 1-10 of 80
ASTM D570: Standard Test Method for Water Absorption of Plastics
Abstract: This test method covers the determination of the relative rate of absorption of water by plastics when immersed. This test method is intended to apply to the testing of all types of plastics, including cast, hot-molded, and cold-molded resinous products, and both homogeneous and laminated plastics in rod and tube form and in sheets 0.13 mm [0.005 i...
ASTM C505M: Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric)
Abstract: This specification covers nonreinforced concrete pipe with rubber gasket joints to be used for the conveyance of irrigation water with working pressures, including hydraulic transients, as shown in Table 1.
This ...
This ...
ASTM C1492: Standard Specification for Concrete Roof Tile
Abstract: This specification covers concrete tiles intended for the use as roof covering where durability and appearance are required to provide a weather-resistant surface of specified design.
Tiles are manufactured from portland ...
Tiles are manufactured from portland ...
ACI 211.1: Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete
Abstract: This Standard Practice describes methods for selecting proportions for hydraulic cement concrete made with and without other cementitious materials and chemical admixtures. This concrete consists of normal and/or highdensity ...
ACI 211.2: Standard Practice for Selecting Proportions for Structural Lightweight Concrete
Abstract: Discussion in this standard is limited to structural grade, lightweight aggregates, and structural lightweight-aggregate concrete. Structural lightweight-aggregate concrete is defined as concrete which: (a) is made with ...
ASTM C1262: Standard Test Method for Evaluating the Freeze-Thaw Durability of Dry-Cast Segmental Retaining Wall Units and Related Concrete Units
Abstract: This test method covers the resistance to freezing and thawing of dry-cast segmental retaining wall (SRW) units (see Specification C1372) and related concrete units. Units are tested in a test solution that is either water or 3 {}aline solution depending on the intended use of the units in actual service.
NOTE 1—Related concrete units inc...
NOTE 1—Related concrete units inc...
ASTM C1623: Standard Specification for Manufactured Concrete Masonry Lintels
Abstract: This specification covers concrete masonry lintels (beams) that are solid in cross-section, are reinforced for flexure, and are made from hydraulic cement, water, and mineral aggregates with or without the inclusion of other materials. These lintels are suitable for both loadbearing and nonloadbearing applications.
NOTE 1—This specificati...
NOTE 1—This specificati...
ASTM C118M: Standard Specification for Concrete Pipe for Irrigation or Drainage (Metric)
Abstract: This specification covers nonreinforced concrete pipe to be used for the conveyance of irrigation water with working pressures, including hydraulic transients, as shown in Table 1 and for use in drainage.
This specification ...
This specification ...
ASTM C73: Standard Specification for Calcium Silicate Brick (Sand-Lime Brick)
Abstract: This specification covers brick made principally from sand and lime and intended for use in brick masonry. Two grades of brick are covered:
Grade SW—Brick intended for use where exposed to temperature below freezing in the presence of moisture.
NOTE 1—As a typical example, brick used for foundation courses and parapets in the no...
Grade SW—Brick intended for use where exposed to temperature below freezing in the presence of moisture.
NOTE 1—As a typical example, brick used for foundation courses and parapets in the no...
ASTM C1124/C1124M: Standard Test Method for Kerosene Retention of Asbestos
Abstract: This test method covers the determination of the kerosene retention capacity of asbestos fiber by filtering after mixing and measuring the volume of liquid retained by difference.
The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; the...
The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; the...