درباره ما
ACI - American Concrete Institute: Recent submissions
Now showing items 561-580 of 636
-
ACI 117
Abstract: This specification designates standard tolerances for concrete construction.
The indicated tolerances govern unless otherwise specified.
Tolerances in this specification are for typical concrete construction and ...Subject(s) : architectural concrete , concrete , construction , drilled piers , formwork , foundation , mass concrete , pier , precast concrete , prestressed concrete , reinforced concrete , reinforcement , specification , splice , tilt-up concrete , tolerances , -
ACI 330.1M
Abstract: This specification covers requirements for the construction of unreinforced concrete parking lots and site paving on grade, including attached and integral curbs. Site paving includes entrance and exit lanes as well as ... -
ACI 332
Abstract: This Code, when legally adopted as part of a general building code, provides minimum requirements for design and construction of residential concrete elements. In areas without a legally adopted building code, this Code ...Subject(s) : admixtures , aggregates , air entrainment , anchorage (structural) , backfill , building codes , calcium chloride , cements , cold weather construction , compressive strength , concrete construction , concrete construction joints , concretes , contraction joints , cover , curing , flexural strength , floors , footings , formwork (construction) , foundation walls , foundations , hot weather construction , inspection , loads (forces) , materials , mixing , mixture proportioning , placing , plain concrete , reinforced concrete , reinforcing steels , residential , serviceability , slab-on-ground , slabs , specifications , strength , structural analysis , structural concrete , structural design , sulfates exposure , walls , water , welded wire reinforcement , -
ACI SP-181
Abstract: PREFACE: This specid publication addresses important issues that are at the center of future developments in concrete pavement design and construction specification. The papers provided in this document ... -
ACI 311.7
Abstract: Services specified—This Reference Specification sets the minimum requirements for quality assurance inspection of cast-in-place concrete whenever inspection services are required by the local ... -
ACI 423.8R
Abstract: This report includes a review and summary of the following:
• Guide specifications and training as applied to grouted post-tensioning tendons;
• Potential problem areas in grouted systems;
• ...Subject(s) : anchorage , bonded , corrosion , duct , durability , grout , post-tensioning , prestressed , repair , strand , tendon , -
ACI 122R
Abstract: Introduction
The recurrence of energy crises, coupled with increased public awareness and government action, have encouraged the development of building codes that include energy-conservation requirements. ...Subject(s) : aggregate , cement paste , concrete , concrete masonry unit , moisture , specific heat , thermal conductivity , thermal diffusivity , thermal resistance , -
ACI 374.1
Abstract: This document defines minimum acceptance criteria for new reinforced concrete moment frames designed for regions of high seismic risk or for structures assigned to satisfy high seismic performance or design categories, ... -
ACI 544.4R
Abstract: INTRODUCTION
Steel fiber reinforced concrete (SFRC) and mortar made with hydraulic cements and containing fine or fine and coarse aggregates along with discontinuous discrete steel fibers are considered ...Subject(s) : beams (supports) , cavitation , compressive strength , concrete slabs , creep properties , fatigue (materials) , fiber reinforced concretes , fibers , flexural strength , freeze-thaw durability , metal fibers , mortars (material) , structural design , -
ACI 364.3T
Abstract: Introduction
When epoxy-coated steel reinforcement is exposed in a repair area, the exposed reinforcement requires treatment prior to repair material placement.Subject(s) : coating , corrosion , corrosion inhibitor , electrical resistance , epoxy-coated , reinforcing bars , reinforcing steel , repair , ring corrosion , sacrificial anode , -
ACI 440.5M
Abstract: Work specified—This Specification covers cast-in-place structural concrete reinforced with fiber-reinforced polymer (FRP) bars except where other provisions are specified in the Contract Documents.
Work ... -
ACI CCS-3
Abstract: PREFACE
This is the third booklet in the Concrete Craftsman Series published by the American Concrete Institute. The first booklet, Slabs on Grade covers placing, curing and finishing. The ... -
ACI 506.4R
Abstract: INTRODUCTION
The purpose of this report is to present procedures that can be used to evaluate the quality and properties of in-place shotcrete.
Considerable literature is available on testing fresh ...Subject(s) : brooming , construction practices , cracking (fracturing) , defects , dry mix , finishing , in-situ testing , inspection , lenses , nozzleman , overspray , permeability , quality , sags , sand pockets , screeding , shotcrete , trowel cutting , visual appearance voids , wet mix. , -
ACI 327R
Abstract: INTRODUCTION
Roller-compacted concrete (RCC) is an economical, fast construction candidate for many pavement applications. Because of its relatively coarse surface, RCC has traditionally been used for ... -
ACI 332M
Abstract: This Code, when legally adopted as part of a general building code, provides minimum requirements for design and construction of residential concrete elements. In areas without a legally adopted building code, this Code ...Subject(s) : admixtures , aggregates , air entrainment , anchorage (structural) , backfill , building codes , calcium chloride , cements , cold weather construction , compressive strength , concrete construction , concrete construction joints , concretes , contraction joints , cover , curing , flexural strength , floors , footings , formwork (construction) , foundation walls , foundations , hot weather construction , inspection , loads (forces) , materials , mixing , mixture proportioning , placing , plain concrete , reinforced concrete , reinforcing steels , residential , serviceability , slab-on-ground , slabs , specifications , strength , structural analysis , structural concrete , structural design , sulfates exposure , walls , water , welded wire reinforcement. , -
ACI ITG-4.3R
Abstract: This document addresses the material and design considerations when using normalweight concretes having specified compressive strengths of 6000 psi (41 MPa) or greater in structures designed for moderate to high seismic ...Subject(s) : bond , confinement , drift , flexure , high-strength concrete , highyield-strength reinforcement , seismic application , shear , stress block , strutand-tie , -
ACI 364.3R
Abstract: Purpose and scope
The purpose of this report is to provide a source of information on the evaluation of concrete structures (except those subjected to seismic effects) prior to rehabilitation. This is ...Subject(s) : buildings: concrete , condition survey: evaluation , field observation , historic structures: nondestructive evaluation , rehabilitation: sampling , service history: testing , -
ACI 355.4
Abstract: This standard applies only to post-installed adhesive anchors as defined herein.
Adhesive anchors resist tension loads with a combination of adhesion and mechanical bond (micro-interlock). Different anchor designs ...Subject(s) : adhesive anchors , cracked concrete , fasteners , post-installed anchors , qualification procedures , uncracked concrete , -
ACI 352.1R
Abstract: Information and design recommendations have been summarized by Joint ACI-ASCE Committee 426 (1974, 1977). This guide is an update of ACI 352.1R-89 (Joint ACIASCE Committee 352 1989), based on research information ...Subject(s) : connection , flat plate , flat slab , joint , lateral drift , posttensioned , punching shear , seismic , shear reinforcement , slab-column ,