درباره ما
Standard Practice for Preparing Specimens of Hydraulic Erosion Control Products for Index Property Testing
ASTM D7986-25
Organization:
ASTM - ASTM International
Year: 2025
Abstract: 5.1 This practice is intended to simulate mixing of HECP products as would be mixed on a job or project site but in a laboratory environment on a smaller scale. Dried samples are not necessarily intended to represent a field application of HECP products but would be representative of the correct amount of material applied to a known area and provide a basis for consistent and repeatable index property testing. Manufacturers and requesting agencies typically use this standard as a means of quality assurance. Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it and the suitability of the equipment and facility used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some, but not all, of those factors.
Collections
:
-
Statistics
Standard Practice for Preparing Specimens of Hydraulic Erosion Control Products for Index Property Testing
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T19:28:05Z | |
| date available | 2025-09-30T19:28:05Z | |
| date copyright | 2025 | |
| date issued | 2025 | |
| identifier other | d7986-25.pdf | |
| identifier uri | http://yse.yabesh.ir/std;jsery=autho/handle/yse/343732 | |
| description abstract | 5.1 This practice is intended to simulate mixing of HECP products as would be mixed on a job or project site but in a laboratory environment on a smaller scale. Dried samples are not necessarily intended to represent a field application of HECP products but would be representative of the correct amount of material applied to a known area and provide a basis for consistent and repeatable index property testing. Manufacturers and requesting agencies typically use this standard as a means of quality assurance. Note 1: The quality of the result produced by this standard is dependent on the competence of the personnel performing it and the suitability of the equipment and facility used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some, but not all, of those factors. | |
| language | English | |
| title | Standard Practice for Preparing Specimens of Hydraulic Erosion Control Products for Index Property Testing | en |
| title | ASTM D7986-25 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2025 | |
| contenttype | fulltext | |
| scope | 1.1 This practice specifies a set of instructions for preparing samples of hydraulic erosion control products (HECPs) for index property testing. 1.2 Units—The values stated in SI units are being regarded as standard. No other units of measurement are included in this standard. Reporting of test results in units other than SI shall not be regarded as nonconformance with this standard. 1.3 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026. 1.3.1 For purposes of comparing measured or calculated value(s) with specified limits, the measured or calculated value(s) shall be rounded to the nearest decimal or significant digits in the specified limits. 1.3.2 The procedures used to specify how data are collected/recorded or calculated, in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that generally should be measured. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the users objectives; and it is common practice to increase or reduce the significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in the analytical methods for engineering design. 1.4 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/D7986-25 |