درباره ما
SAE - SAE International: Recent submissions
Now showing items 661-680 of 16264
-
Thermal Sensitive Inflation Pressure Release Devices for Tubeless Aircraft Wheels
Abstract: The focus of this SAE Aerospace Standard (AS) is the integration of thermally actuated pressure release devices, hereafter referred to as fuse plugs, with the wheel and brake assembly. It does not address the manufacturing, ... -
Supplemental Propulsion System Performance Station Designation
Abstract: This SAE Aerospace Information Report (AIR) supplements the AS755 performance station designation system for complex or unconventional propulsion cycles and their derivatives.The station numbering conventions presented ... -
Inserts, Screw Thread, Helical Coil 19Cr-9.2Ni, Corrosion Resistant Steel, Procurement Specification for
Abstract: This specification covers closely-wound helical coil, screw thread inserts made of a corrosion resistant steel formed wire with a chemical composition in accordance with Table 1 and identified under the Unified Numbering ... -
AS5553B, Counterfeit Electrical, Electronic and Electromechanical (EEE) Parts; Avoidance, Detection, Mitigation, and Disposition Verification Criteria
Abstract: This set of criteria can be utilized to assess compliance to AS5553B, Aerospace Standard Counterfeit Electrical, Electronic and Electromechanical (EEE) Parts; Avoidance, Detection, Mitigation, and Disposition. -
Bolts and Screws, Steel, Corrosion and Moderate Heat Resistant Heat Treated, Roll Threaded
Abstract: This procurement specification covers aircraft quality bolts and screws made from a corrosion and moderate heat-resistant martensitic iron base alloy of the type identified under the Unified Numbering System as UNS S41800 ... -
Coupling Assemblies, Quick Disconnect, Automatic Shutoff
Abstract: This specification establishes requirements for automatic shutoff, quick-disconnect coupling assemblies for fuel and oil lines. -
-
Hose Assembly and Tubing, Polytetrafluoroethylene, Cleaning Methods for
Abstract: This SAE Aerospace Standard (AS) describes cleaning methods for four cleanliness levels of polytetrafluoroethylene hose assemblies and rigid tube assemblies for use in aerospace systems. -
Aircraft Ground Deicing/Anti-Icing Processes
Abstract: This document establishes the minimum requirements for ground based aircraft deicing/anti-icing methods and procedures to ensure the safe operation of aircraft during icing conditions on the ground. This document does not ... -
JAUS Unmanned Ground Vehicle Service Set
Abstract: This document defines a set of standard application layer interfaces called JAUS Unmanned Ground Vehicle Services. JAUS Services provide the means for software entities in an unmanned system or system of unmanned systems ... -
Impact of Copper Contamination on the Thermal Stability of Jet Fuels
Abstract: This SAE Aerospace Information Report (AIR) discusses the sources of Copper in aviation jet fuels, the impact of Copper on thermal stability of jet fuels and the resultant impact on turbine engine performance, and potential ... -
Verification Methods for AS5653 Network Terminal
Abstract: This document was prepared by the SAE AS-1A2 Committee to establish techniques for validating the Network Terminal (NT) complies with the NT requirements specified in AS5653, Revision B. Note that this verification document ... -
Cable, Lightweight Optimized High Speed, Data Quad, 110 Ohm, 200 °C
Abstract: Scope is unavailable. -
Hose Assembly, Polytetrafluoroethylene, Metallic Braid Reinforced, 5080 psi (35000 kPa), 400 °F (204 °C), Aircraft Hydraulic Systems
Abstract: This document defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic braid reinforced, hose assembly suitable for use in 400 °F (204 °C), 5080 psi (35000 kPa) aircraft hydraulic systems.NOTE: The SI ... -
JAUS / SDP Transport Specification
Abstract: This SAE Aerospace Standard (AS) specifies a data communications layer for the transport of messages defined by the Joint Architecture for Unmanned Systems (JAUS) or other Software Defined Protocols (SDP). This Transport ... -
Insert, Screw Thread, Self-Locking, UNS S66286, Locked In, Key Locked Procurement Specification For
Abstract: This procurement specification covers inserts made from A286 alloy (UNS S66286) which have self-locking internal threads and integrated locking keys to positively secure the insert against rotation when properly installed ...