درباره ما
DIN - Deutsches Institut für Normung e. V.: Recent submissions
Now showing items 901-920 of 22183
-
DIN ISO 19600
Abstract: Scope: This International Standard provides guidance for establishing, developing, implementing, evaluating, maintaining and improving an effective and responsive compliance management system within an organization. The ... -
DIN EN ISO 17751-2
Abstract: Scope: This part of ISO 17751 specifies a method for the identification, qualitative, and quantitative analysis of cashmere, wool, other speciality animal fibres, and their blends using scanning electron microscopy (SEM). ... -
DIN EN ISO 17348
Abstract: Scope: This International Standard provides guidelines and requirements for material selection of both seamless casing and tubing, and downhole equipment for CO2 gas injection and gas production wells with high pressure ... -
DIN EN 10303
Abstract: Scope: This European Standard defines the grades of thin non-oriented magnetic steel strip and sheet in nominal thicknesses of 0,05 mm, 0,10 mm, 0,15 mm, 0,20 mm, 0,25 mm, 0,27 mm, 0,30 mm and 0,35 mm, and of thin ... -
DIN EN ISO 16140-2
Abstract: Scope: This part of ISO 16140 specifies the general principle and the technical protocol for the validation of alternative, mostly proprietary, methods for microbiology in the food chain. Validation studies according to ... -
DIN EN 10244-1
Abstract: Scope: This part of this European Standard specifies the requirements for the mass, other properties and testing of non-ferrous metal coatings on steel wire and steel wire products of circular or other cross-section. This ... -
DIN EN 16877
Abstract: Scope: This method of analysis is applicable to the determination of HT-2 toxin (HT2) in the tested range of 22 μg/kg to 178 μg/kg, T-2 toxin (T2) in the tested range of 7 μg/kg to 50 μg/kg, Deoxynivalenol ... -
DIN ISO 3034
Abstract: Scope: This International Standard specifies a method for determining the single sheet thickness of corrugated fibreboard intended for use in the manufacture of packing cases. This International Standard is applicable to ... -
VG 85605-3
Abstract: Scope: Diese Norm legt die schlauchseitigen Stutzenteile und Klemmfassungen der Schlaucharmaturen für Schläuche nach VG 85605-4 fest, für die in VG 85328-2, DIN EN 14420-2 und DIN EN 14420-3 keine Festlegungen ... -
VG 96926-1
Abstract: Scope: Diese Norm gilt in Verbindung mit VG 95319-2, VG 96926-2 und VG 96926-3 für zweipolige Steckvorrichtungen mit Schutzkontakt. Bei Anwendung dieser Steckvorrichtungen sind die Bestimmungen nach DIN VDE 0620-1 ... -
DIN EN 754-8
Abstract: Scope: This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn porthole tubes with an outside diameter (OD) from 3 mm to 350 mm (round tube, see Figure 1) or with ... -
DIN EN 438-2
Abstract: Scope: This European Standard specifies the methods of test for determination of the properties of high-pressure decorative laminates as defined in Clause 3. These methods are primarily intended for testing the sheets ... -
-
DIN EN 61800-7-304
Abstract: Scope: This part of IEC 61800 specifies the mapping of the profile type 4 (SERCOS) specified in IEC 61800-7-204 onto different network technologies. – SERCOS I / II, see Clause 5, – SERCOS III, see Clause 6, ... -
DIN EN ISO 9202
Abstract: Scope: This International Standard specifies a range of fineness of precious metal alloys (excluding solders) recommended for use in the field of jewellery. National legal requirements for the designation, marking, and ... -
DIN EN ISO 16891
Abstract: Scope: This International Standard specifies a standard reference test method useful to assess the relative degradation characteristics of cleanable filter media for industrial applications under standardized simulated ... -
DIN SPEC 91351
Abstract: Scope: This DIN SPEC defines requirements for the strength testing for photovoltaic wafers by use of uniaxially bending tests for the experimental setup, procedure and evaluation. -
DIN EN ISO 7500-1
Abstract: Scope: This part of ISO 7500 specifies the calibration and verification of tension/compression testing machines. The verification consists of: — a general inspection of the testing machine, including its accessories ... -
DIN EN ISO 2746
Abstract: Scope: This International Standard describes two test methods of high voltage testing: — Test A is used to detect and locate defects in vitreous and porcelain enamels; — Test B is used to detect and locate ... -