درباره ما
DIN EN ISO 4759-3
English -- Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016);
German -- Toleranzen fuer Verbindungselemente - Teil 3: Scheiben fuer Schrauben und Muttern - Produktklassen A, C und F (ISO 4759-3:2016)
Organization:
DIN - Deutsches Institut fš?r Normung e. V.
Year: 2016
Abstract: Scope: This part of ISO 4759 specifies tolerances for flat washers of product grades A, C and F with nominal diameters of 1 mm to 150 mm inclusive, designed to be used in bolted joints in combination with bolts, screws, studs and nuts. This part of ISO 4759 may be applied to non-flat washers however it does not include all the tolerances related to these washers. It applies to non-captive and captive washers, and to standard and non-standard washers. It does not apply to dynamic disc springs. Washers of product grades F and A are intended to be used with bolts, screws, studs and nuts of product grades A and B; washers of product grade C are intended to be used with bolts, screws, studs and nuts of product grade C. NOTE The product grade refers to a specific tolerance range related to dimensional and geometrical characteristics (product grade F for fine tolerances, product grade A for precise tolerances, product grade C for large tolerances). Annex A presents tolerances taken from ISO 286-1 and ISO 286-2.
Collections
:
-
Statistics
DIN EN ISO 4759-3
Show full item record
| contributor author | DIN - Deutsches Institut fš?r Normung e. V. | |
| date accessioned | 2017-10-18T11:04:35Z | |
| date available | 2017-10-18T11:04:35Z | |
| date copyright | 2016.12.01 | |
| date issued | 2016 | |
| identifier other | QZVVSFAAAAAAAAAA.pdf | |
| identifier uri | http://yse.yabesh.ir/std;jsessioutho4703177793325273135A68A10958014A0Fa/handle/yse/234607 | |
| description abstract | Scope: This part of ISO 4759 specifies tolerances for flat washers of product grades A, C and F with nominal diameters of 1 mm to 150 mm inclusive, designed to be used in bolted joints in combination with bolts, screws, studs and nuts. This part of ISO 4759 may be applied to non-flat washers however it does not include all the tolerances related to these washers. It applies to non-captive and captive washers, and to standard and non-standard washers. It does not apply to dynamic disc springs. Washers of product grades F and A are intended to be used with bolts, screws, studs and nuts of product grades A and B; washers of product grade C are intended to be used with bolts, screws, studs and nuts of product grade C. NOTE The product grade refers to a specific tolerance range related to dimensional and geometrical characteristics (product grade F for fine tolerances, product grade A for precise tolerances, product grade C for large tolerances). Annex A presents tolerances taken from ISO 286-1 and ISO 286-2. | |
| language | English | |
| title | DIN EN ISO 4759-3 | num |
| title | English -- Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016) | en |
| title | German -- Toleranzen fuer Verbindungselemente - Teil 3: Scheiben fuer Schrauben und Muttern - Produktklassen A, C und F (ISO 4759-3:2016) | other |
| type | standard | |
| page | 19 | |
| status | Active | |
| tree | DIN - Deutsches Institut fš?r Normung e. V.:;2016 | |
| contenttype | fulltext |