درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 421-440 of 507
-
ECA EIA-850
Abstract: Purpose
This document outlines the process and document submission requirements for manufacturers of an integrated passive device (IPD) to register their product. Registration is for the purposes of ... -
ECA 293
Abstract: This standard defines the parameters used to describe the electrical characteristics of Sonic Wire Delay Lines with Magnetostriction Transducers for pulse applications. Methods for measuring these parameters are also prescribed. -
ECA TEP197-A
Abstract: Introduction
In accordance with the Radiation Control for the Health and Safety Act of 1968, cathode ray tube (CRT) manufacturers are required to submit an initial report to the Center for Devices and ... -
ECA EIA-726
Abstract: This Standard covers requirements for taping surface mount components generally smaller than 2.0 X 1.2 mm and requiring high precision taping for automatic handling. Refer to EIA 481-1 for current industry Standard for 8 ... -
ECA EIA-540CAAE-A
Abstract: The relay sockets, of assessed quality, covered by this detail specification have:
a) The ability to mate with 3PDT 10 ampere-rated hermetically sealed relay.
b) A rated voltage not to exceed 250 volts (rms) at sea ... -
ECA EIA-364-25D
Abstract: This standard establishes a test method to be followed for probe damage testing; intended primarily for round socket contacts in electrical connectors and possibly applicable to other type contacts as well. This test is ... -
ECA ACH-2000
Abstract: ACH-2000 defines those new technologies which have been submitted and approved by EM-ACH for registration of new technologies. -
ECA 272
Abstract: This standard provides a definition of voltage jump and establishes a general test method including the necessary circuit constants.
PURPOSE
The purpose of this standard is to provide a uniform ... -
ECA EIA-741
Abstract: This standard defines the dimensions and interconnections of 133.35 mm (5.25 in) small form factor disk drives.
The purpose of this standard is to define the external characteristics of small form factor disk drives ... -
ECA EIA-965
Abstract: This specification defines the plug, guide/strain relief shell, and latching requirements for the Mini Multilane 12 Gbs 12X Shielded Connector based upon the mating interface defined herein.
The SFF Committee activities ... -
ECA EIA/ECA-364-07C
Abstract: This standard establishes a test method to determine the straightness of contacts by measuring a total indicator reading (TIR) value. Axial concentricity can be measured after crimping to determine axial deformation. -
ECA 235-C
Abstract: The following codes are recommended as standards to be employed with traveling wave tubes, klystron tubes or crossed field devices. that are equipped with flying leads. It is intended that the insulation of the leads be ... -
ECA 405
Abstract: This standard covers acceptable instrumentation and procedures for the measurement of flutter in instrumentation magnetic recording equipment. The purpose of this standard is to promote interchangeability and to eliminate ... -
ECA EIA-364-15A
Abstract: This standard establishes a test method to determine the pin contact strength for contact sizes 20 and smaller when subjected to a defined bending stress (or moment). -
ECA TEP105-16-A
Abstract: Introduction
An excited CRT raster is designed to give the impression of a continuously excited display without any flicker or scan line structure. High fiequeixj, field refresh rates and closely spaced ... -
ECA 197-A
Abstract: This Standard covers iron-core power filter inductors for use in electronic equipment where long life, reliability and continuity of operation are essential. -
ECA EIA/ECA-364-91A
Abstract: This standard establishes a test method to determine the susceptibility of an electrical connector or socket system to the potential degradation mechanism of a dust/fiber environment common to an office or manufacturing ... -
ECA EIA-809
Abstract: Introduction
Solid electrolytic tantalum capacitors are those devices having a sintered tantalum anode that incorporates a solid electrolyte counter-electrode layer.
They are polar devices, having ...