درباره ما
ECIA - Electronic Components Industry Association: Recent submissions
Now showing items 441-460 of 507
-
ECA 580BA00
Abstract: Introduction to a Blank Detail Specification
A blank detail specification is a supplementary document to the Sectional Specification and contains requirements for style and layout and minimum content ... -
ECA EIA-364-30A
Abstract: This procedure applies to electrical connectors and sockets.
Object
This standard describes a test method to measure capacitance from 1 kHz to 1 MHz. -
ECA TEP 192
Abstract: PREFACE
This glossary of terms and definitions was prepared by the EIA Tube Engineering Panel Advisory Council (TEPAC) JT-20 Committee on Electro-Optic Devices. In its preparation, use was made of input and suggestions ... -
ECA EIA-540CA00
Abstract: The realy sockets, of assessed quality, covered by this detail specification have:
a) the ability to mate with -
b) a rated voltage not to exceed -
c) the ability to withstand -
Object
The object ... -
ECA CB6-A
Abstract: INTRODUCTION AND SCOPE
This document has been compiled in response to a generally expressed desire on the part of both users and manufacturers for a guide to the use of quartz crystal units for ... -
ECA EIA-364-88A
Abstract: This standard establishes a test method to determine the residual magnetism of a connector after exposure to a specified magnetic field.
NOTE — Connectors with a relative magnetism of 2 MU as determined by ... -
ECA EIA/ECA-886-A
Abstract: Introduction
This specification defines the requirements for a family of thick film chip resistor arrays in ceramic with various configurations and package sizes. -
ECA TEP106-B
Abstract: INTRODUCTION
This publication prescribes the administrative procedures for the orderly assignment of type designations and registration in the Worldwide Type Designation System for TV Picture Tubes and ...Subject(s) : Definition of Worldwide Type designation System (WTDS) for TV Picture Tubes and Monitor Tubes , -
ECA 402
Abstract: This standard defines and characterizes liquid rosin fluxes of three types.
PURPOSE
The purpose of this standard is to provide an industry standard for liquid rosin fluxes used for soldering. -
ECA EIA/ECA-674-A
Abstract: This specification defines the dimensions and connector locations of 45 millimeter (1.8 inch) small form factor disk drives.
Purpose
The purpose of this specification is to define the external characteristics ... -
ECA CB-11
Abstract: SCOPE AND INTRODUCTION
This document provides guidelines for the use of multilayer ceramic chip capacitors, their design and construction as well as handling, mounting .and connection requirements. ... -
ECA 540AB00
Abstract: The Chip Carrier Sockets of assessed quality covered by this detail specification shall have:
a) Maximum enclosure of (maximum length, width, and height dimensions).
b) A working voltage not exceeding _ volts (rms). ... -
ECA EIA-364-86
Abstract: Objective
The objective of this test procedure is to determine the effectiveness of polarization/coding keys when a connector pair is misregistered (improperly mated). -
ECA ECCB-954
Abstract: This document defines the requirements for establishing processes to identify and control the introduction of hazardous substances (HS) into its products. In the event that hazardous substances are introduced into the ... -
ECA 540D000-A
Abstract: This Sectional Specification relates to the plug-in sockets designed for In-Line electronic packages of assessed quality. The purpose of these sockets is to provide interchangeable devices for use on panel boards, printed ... -
ECA EIA-520DAAA
Abstract: The standard size, one pole watertight toggle switches of certified quality covered by this detail specification
a) mount in a 12.4 mm (.4 9 inch) diameter mounting hole.
b) have a maximum rated voltage of 277 ... -
ECA TEP 196
Abstract: Purpose: This procedure was established so that a consistent method would be available over time and Committee membership changes. -
ECA EIA-364-09C
Abstract: This standard establishes a method to determine the effects caused by subjecting electrical connectors or contacts to the conditioning action of mating and unmating, simulating the expected life of the connectors.