Now showing items 501-520 of 636

    • ACI 303R 

      Type: standard
      Source: ACI - American Concrete Institute:;2012
      Organization : ACI - American Concrete Institute
      Abstract: INTRODUCTION
      This guide presents recommendations for cast-in-place architectural concrete that is exposed to view. Architectural concrete requires special care in the selection of concrete materials, ...
    • ACI 343R 

      Type: standard
      Source: ACI - American Concrete Institute:;2004
      Organization : ACI - American Concrete Institute
      Abstract: These recommendations, reported by the joint ACI-ASCE Committee 343 on Concrete Bridge Design, provide currently acceptable guidelinesfor the analysis and design of reinforced, prestressed, and partially prestressed ...
    • ACI 117M 

      Type: standard
      Source: ACI - American Concrete Institute:;2010
      Organization : ACI - American Concrete Institute
      Abstract: This specification designates standard tolerances for concrete construction.
      The indicated tolerances govern unless otherwise specified.
      Tolerances in this specification are for typical concrete construction and ...
      Subject(s) : architectural concrete , concrete , construction , drilled piers , formwork , foundation , mass concrete , pier , precast concrete , prestressed concrete , reinforced concrete , reinforcement , specification , splice , tilt-up concrete , tolerances ,
    • ACI 437.2M 

      Type: standard
      Source: ACI - American Concrete Institute:;2013
      Organization : ACI - American Concrete Institute
      Abstract: The requirements of this code shall govern for the evaluation of safety and serviceability of members in existing concrete structures by load testing.
      The requirements of this code shall apply to reinforced concrete ...
    • ACI 503.3 

      Type: standard
      Source: ACI - American Concrete Institute:;2010
      Organization : ACI - American Concrete Institute
      Abstract: This reference specification covers the production of a skid-resistant surface on hardened concrete by the application of epoxy and aggregate.
      The provisions of this reference specification shall govern unless otherwise ...
      Subject(s) : aggregates , coatings , concrete pavements , epoxy resins , hardened concrete , quality control , skid resistance , specification , standards ,
    • ACI 506.5R 

      Type: standard
      Source: ACI - American Concrete Institute:;2009
      Organization : ACI - American Concrete Institute
      Abstract: This guide is intended for owner, designer, specifier, and inspection and testing personnel interested in or in need of information and background on the application of underground shotcrete. The guide briefly discusses ...
      Subject(s) : acceptance criteria , batching , inspection , methods of payment , mine and tunnel support systems , mixing and placement equipment , mixture proportioning , preconstruction and construction testing , quality assurance , quality control , safety , shotcrete , shotcrete application ,
    • ACI 549.3R 

      Type: standard
      Source: ACI - American Concrete Institute:;2009
      Organization : ACI - American Concrete Institute
      Abstract: This report introduces glass fiber-reinforced concrete premix and reviews the state of knowledge regarding selection of materials, mixture proportions, and manufacturing methods for producing premix products. Also highlighted ...
      Subject(s) : cement boards , cement panels , cement-based composites , composite materials , concrete panels , ductility , durability , engineering properties , ferrocement , fiber-reinforced cement-based materials , fibers , flexural strength , glass fiber-reinforced concrete , glass fibers , manufacturing methods , mesh reinforcement , premix , toughness ,
    • ACI SP-175 

      Type: standard
      Source: ACI - American Concrete Institute:;1998
      Organization : ACI - American Concrete Institute
      Abstract: Introduction
      In military terminology, terrorism is considered low-grade warfare. As such, in any of the principles used to design military targets are applicable to the protective design of civilian ...
    • ACI C-27 

      Type: standard
      Source: ACI - American Concrete Institute:;1994
      Organization : ACI - American Concrete Institute
      Abstract: Preface: ACI Compilations combine material previously published in Institute periodicals to provide compact and ready reference on specific topics. The Material in a compilation does not necessarily represent ...
    • ACI 304.2R 

      Type: standard
      Source: ACI - American Concrete Institute:;2008
      Organization : ACI - American Concrete Institute
      Abstract: INTRODUCTION
      ACI defines pumped concrete as concrete that is transported through hose or pipe by means of a pump. Pumping concrete through metal pipelines by piston pumps was introduced in the United ...
      Subject(s) : admixtures , aggregate gradation , aggregates , cement content , coarse aggregates , concrete construction , concretes , conveying , couplings , fine aggregates , fineness modulus , lightweight aggregate concrete , lightweight aggregates , mix proportioning , pipeline , placing , placing boom , pozzolans , pumped concrete , pumps , quality control , water content ,
    • ACI 349 

      Type: standard
      Source: ACI - American Concrete Institute:;2007
      Organization : ACI - American Concrete Institute
      Abstract: This Code provides the minimum requirements for the design and construction of nuclear safety related concrete structures and structural elements for nuclear power generating stations. Safety related structures and ...
    • ACI 503.1-503.4 

      Type: standard
      Source: ACI - American Concrete Institute:;2003
      Organization : ACI - American Concrete Institute
      Abstract: This specification describes the work of bonding hardened concrete, steel, wood, brick and other materials to hardened concrete with a multi-component epoxy adhesive such as defined for this purpose in ASTM C 881. It ...
      Subject(s) : adhesives , aggregates , aluminum , bond (concrete to concrete) , bonding , bricks , coatings , concrete construction , concrete pavements , copper , epoxy resins , fresh concretes , hardened concrete , mortars (material) , quality control , repairs , resurfacing , safety , skid resistance , specifications , standards , steels , wood ,
    • ACI 364.4T 

      Type: standard
      Source: ACI - American Concrete Institute:;2010
      Organization : ACI - American Concrete Institute
      Abstract: Introduction
      In cases where a structural evaluation is to be performed, knowledge of member sizes, reinforcing details, and material properties is generally required. In cases where this information ...
      Subject(s) : foundation capacity , gravity and lateral loads , investigation program , load capacity , load testing , material properties , structural configuration , visual examination ,
    • ACI SP-200 

      Type: standard
      Source: ACI - American Concrete Institute:;2001
      Organization : ACI - American Concrete Institute
    • ACI 440.6 

      Type: standard
      Source: ACI - American Concrete Institute:;2008
      Organization : ACI - American Concrete Institute
      Abstract: This specification describes permitted constituent materials, limits on constituent volumes, and minimum performance requirements for carbon and glass fiber-reinforced polymer (FRP) bars to be used as reinforcement for ...
      Subject(s) : carbon fiber , concrete , concrete construction , fiber-reinforced polymer reinforcement , FRP reinforced concrete , glass fiber , specification ,
    • ACI 550.3M 

      Type: standard
      Source: ACI - American Concrete Institute:;2013
      Organization : ACI - American Concrete Institute
      Abstract: This Standard defines requirements for a certain type of hybrid special moment frame composed of precast concrete beams jointed at their connections to columns that are continuous past those joints. Whereas these frames ...
    • ACI 318 ERTA 

      Type: standard
      Source: ACI - American Concrete Institute:;2012
      Organization : ACI - American Concrete Institute
    • ACI 351.4 

      Type: standard
      Source: ACI - American Concrete Institute:;2014
      Organization : ACI - American Concrete Institute
      Abstract: This specification covers minimum requirements for cementitious grouting between foundations and equipment and machinery bases. 
      This specification supplements the Contract Documents and provides requirements for ...
    • ACI 503.7 

      Type: standard
      Source: ACI - American Concrete Institute:;2007
      Organization : ACI - American Concrete Institute
      Abstract: This specification describes the work of bonding hardened concrete, steel, wood, brick and other materials to hardened concrete with a multi-component epoxy adhesive such as defined for this purpose in ASTM C 881. It ...
    • ACI SP-170 

      Type: standard
      Source: ACI - American Concrete Institute:;1997
      Organization : ACI - American Concrete Institute
      Abstract: PREFACE
      The Canada Centre for Mineral and Energy Technology (CANMET) of Natural Resources Canada, Ottawa, has played a significant role in Canada for over 33 years in the area of durability of concrete. ...