درباره ما
MIL-C-29600
CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, COMPOSITE, HIGH DENSITY, QUICK COUPLING, ENVIRONMENT RESISTANT, REMOVABLE CRIMP CONTACTS, ASSOCIATED HARDWARE, GENERAL SPECIFICATION FOR
Organization:
NAVY - AS - Naval Air Systems Command
Year: 1989
Abstract: This specification covers miniature, composite, high density, threaded coupling, self locking, circular, environment resistant, electrical connectors utilizing removable crimp contacts, and associated hardware, which are capable of continuous operation within a temperature range of −65° to +175°C. These connectors are supplied under a MIL-STD-790 reliability assurance program. See 6.1 for intended use and applications.
The connectors employ rear release removable pin and socket contacts with crimp termination. The connectors are designed to assure proper orientation of the mating halves prior to electrical circuit closure. The connectors include EMI shielding capability. They also provide electrical continuity between mated shells prior to contact engagement and have the contacts so located as to be protected from handling damage and inadvertent electrical contact. The connectors consist of a composite material with light weight characteristics and, when used with backshells and contacts specified herein, provide high levels of corrosion resistance and durability.
Connectors are designed to be used as a system with backshells and contacts specified herein. When so used, the connectors are capable of performance during or after, as applicable, under the following environmental conditions:
−65° to +175°C. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Systems Engineering and Standardization Department (Code 53), Naval Air Engineering Center, Lakehurst, NJ 08733-5100, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.
a. Random: 41.7 G RMS at rated high and low temperatures without backshell.
49.5 G RMS at ambient temperature with backshell.
b. Sine: 60 G at ambient temperature with backshell.
Altitudes from sea level to 100,000 feet (8 torr). Test voltage will vary with altitude (see Table XII).
Shock as represented by a 3 + 1 milliseconds base half-sine wave peaking at 300 G (see 3.23).
Per MIL-S-901.
Humidity conditions up to 98 percent relative humidity including condensation (see 3.25).
2000 hours exposure to salt-laden atmosphere (see 3.15).
See 4.6.3.
Immersion, in jet fuel, lubrication oil, liquid coolant, hydraulic fluid, gasoline, cleaning compound, defrosting fluid, and solvents (see 3.29).
EMI shielding effectiveness: 100 MHZ to 10 GHZ, minimum attenuation of 50 dB (see 3.27).
Exposure of uncoupled connector to a salt moisture environment (see 3.34).
1500 matings and unmatings (see 3.4.1, and 3.10).
Classification.
Connectors fabricated to this specification are scoopproof, self-locking, quick coupling and are as follows:
a. Series: The series A and B connectors are not intermateable.
A - Utilize MIL-C-38999 insert arrangements.
B - Utilize MIL-C-81511 insert arrangements.
b. Types:
(1) Plugs: Straight.
(2) Receptacles: Wall mounting, both front and rear panel mounting, jam nut mounting. Contains grounding member that makes shell contact prior to contact engagement.
c. Class: R - Environment resisting - conductive shell.
E - Environment resisting.
G - Environment resisting - conductive shell, space grade.
a. Styles:
(1) Connectors ordered with high performance contacts:
H - Pin
J - Socket
The H or J designators are used to indicate a full complement of applicable high performance contacts rated at 1500 cycles of durability, and shall appear in the part number marked on the connector.
(2) Connectors ordered with standard contacts:
P - Pin
S - Socket
The P or S designators are used to indicate a full complement of applicable standard contacts rated at 500 cycles of durability, and shall appear in the part number marked on the connector.
(3) Connectors ordered without contacts:
A - Less pin contacts. Application specifies 500 cycles of durability.
B - Less socket contacts.
K - Less pin contacts. Application specifies 1500 cycles of durability.
L - Less socket contacts.
The A, B, K, or L designators are used to indicate connectors ordered less contacts, and are intended to have other than all standard power contacts installed (example: shielded, coaxial and thermocouple contacts). The A, B, K, or L designator shall appear in the part number marked on the connector.
Connectors ordered less contacts, but intended for assembly with all high performance or all standard contacts, shall have the H or J designator, or the P or S designator, respectively in the part number marked on the connector the same as connectors ordered with a full complement of applicable contacts.
a. Types:
(1) Backshells.
(2) Protective covers.
(3) Dummy stowage receptacles.
(4) Sealing plugs. Intended Use: Connectors, contacts and associated hardware are intended for general military use as a system. Used as such, they are particularly suitable for light weight applications and corrosive environments where EMI shielding is required. a. Connectors specified herein are not fully intermountable with those specified in MIL-C-81511 or MIL-C-38999. See detailed specification sheets to determine if these connectors will meet the desired mounting requirements. b. Connectors specified herein are not intermateable with connectors from any other military specification, even though some of the internal components and subassemblies may be used by other connectors. c. Connectors specified herein are not intended for use with accessory hardware configured with interfaces consisting of features constructed from a metal base material. a. Air Force - MIL-C-29600 Series B are not for use. b. Army - MIL-C-29600 Series B are not for use. c. Navy - Connectors specified herein are not for shipboard jacketed cable applications. WARNING: MIL-C-29600 Series A Connectors are not intended for mating with MIL-C-29600 Series B Connectors. Doing so may result in damage to the contacts or the inserts of the connectors. It is specifically critical with shell sizes 10 and 11 when size 20 contacts are used and with shell size 20 and 21 when size 12 contacts are used. These connectors shall not be located next to each other in any application unless the shell keying has been selected to guarantee that the shells will never allow the mating process to begin. However, series A and B connectors are interchangeable.
The connectors employ rear release removable pin and socket contacts with crimp termination. The connectors are designed to assure proper orientation of the mating halves prior to electrical circuit closure. The connectors include EMI shielding capability. They also provide electrical continuity between mated shells prior to contact engagement and have the contacts so located as to be protected from handling damage and inadvertent electrical contact. The connectors consist of a composite material with light weight characteristics and, when used with backshells and contacts specified herein, provide high levels of corrosion resistance and durability.
Connectors are designed to be used as a system with backshells and contacts specified herein. When so used, the connectors are capable of performance during or after, as applicable, under the following environmental conditions:
−65° to +175°C. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Systems Engineering and Standardization Department (Code 53), Naval Air Engineering Center, Lakehurst, NJ 08733-5100, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter.
a. Random: 41.7 G RMS at rated high and low temperatures without backshell.
49.5 G RMS at ambient temperature with backshell.
b. Sine: 60 G at ambient temperature with backshell.
Altitudes from sea level to 100,000 feet (8 torr). Test voltage will vary with altitude (see Table XII).
Shock as represented by a 3 + 1 milliseconds base half-sine wave peaking at 300 G (see 3.23).
Per MIL-S-901.
Humidity conditions up to 98 percent relative humidity including condensation (see 3.25).
2000 hours exposure to salt-laden atmosphere (see 3.15).
See 4.6.3.
Immersion, in jet fuel, lubrication oil, liquid coolant, hydraulic fluid, gasoline, cleaning compound, defrosting fluid, and solvents (see 3.29).
EMI shielding effectiveness: 100 MHZ to 10 GHZ, minimum attenuation of 50 dB (see 3.27).
Exposure of uncoupled connector to a salt moisture environment (see 3.34).
1500 matings and unmatings (see 3.4.1, and 3.10).
Classification.
Connectors fabricated to this specification are scoopproof, self-locking, quick coupling and are as follows:
a. Series: The series A and B connectors are not intermateable.
A - Utilize MIL-C-38999 insert arrangements.
B - Utilize MIL-C-81511 insert arrangements.
b. Types:
(1) Plugs: Straight.
(2) Receptacles: Wall mounting, both front and rear panel mounting, jam nut mounting. Contains grounding member that makes shell contact prior to contact engagement.
c. Class: R - Environment resisting - conductive shell.
E - Environment resisting.
G - Environment resisting - conductive shell, space grade.
a. Styles:
(1) Connectors ordered with high performance contacts:
H - Pin
J - Socket
The H or J designators are used to indicate a full complement of applicable high performance contacts rated at 1500 cycles of durability, and shall appear in the part number marked on the connector.
(2) Connectors ordered with standard contacts:
P - Pin
S - Socket
The P or S designators are used to indicate a full complement of applicable standard contacts rated at 500 cycles of durability, and shall appear in the part number marked on the connector.
(3) Connectors ordered without contacts:
A - Less pin contacts. Application specifies 500 cycles of durability.
B - Less socket contacts.
K - Less pin contacts. Application specifies 1500 cycles of durability.
L - Less socket contacts.
The A, B, K, or L designators are used to indicate connectors ordered less contacts, and are intended to have other than all standard power contacts installed (example: shielded, coaxial and thermocouple contacts). The A, B, K, or L designator shall appear in the part number marked on the connector.
Connectors ordered less contacts, but intended for assembly with all high performance or all standard contacts, shall have the H or J designator, or the P or S designator, respectively in the part number marked on the connector the same as connectors ordered with a full complement of applicable contacts.
a. Types:
(1) Backshells.
(2) Protective covers.
(3) Dummy stowage receptacles.
(4) Sealing plugs. Intended Use: Connectors, contacts and associated hardware are intended for general military use as a system. Used as such, they are particularly suitable for light weight applications and corrosive environments where EMI shielding is required. a. Connectors specified herein are not fully intermountable with those specified in MIL-C-81511 or MIL-C-38999. See detailed specification sheets to determine if these connectors will meet the desired mounting requirements. b. Connectors specified herein are not intermateable with connectors from any other military specification, even though some of the internal components and subassemblies may be used by other connectors. c. Connectors specified herein are not intended for use with accessory hardware configured with interfaces consisting of features constructed from a metal base material. a. Air Force - MIL-C-29600 Series B are not for use. b. Army - MIL-C-29600 Series B are not for use. c. Navy - Connectors specified herein are not for shipboard jacketed cable applications. WARNING: MIL-C-29600 Series A Connectors are not intended for mating with MIL-C-29600 Series B Connectors. Doing so may result in damage to the contacts or the inserts of the connectors. It is specifically critical with shell sizes 10 and 11 when size 20 contacts are used and with shell size 20 and 21 when size 12 contacts are used. These connectors shall not be located next to each other in any application unless the shell keying has been selected to guarantee that the shells will never allow the mating process to begin. However, series A and B connectors are interchangeable.
Subject: Accessories
Collections
:
Show full item record
| contributor author | NAVY - AS - Naval Air Systems Command | |
| date accessioned | 2017-09-04T18:23:45Z | |
| date available | 2017-09-04T18:23:45Z | |
| date copyright | 32862 | |
| date issued | 1989 | |
| identifier other | IEWUDAAAAAAAAAAA.pdf | |
| identifier uri | http://yse.yabesh.ir/std;query=autho162sear3FCDCAC426159DD6E273C9FCD/handle/yse/206156 | |
| description abstract | This specification covers miniature, composite, high density, threaded coupling, self locking, circular, environment resistant, electrical connectors utilizing removable crimp contacts, and associated hardware, which are capable of continuous operation within a temperature range of −65° to +175°C. These connectors are supplied under a MIL-STD-790 reliability assurance program. See 6.1 for intended use and applications. The connectors employ rear release removable pin and socket contacts with crimp termination. The connectors are designed to assure proper orientation of the mating halves prior to electrical circuit closure. The connectors include EMI shielding capability. They also provide electrical continuity between mated shells prior to contact engagement and have the contacts so located as to be protected from handling damage and inadvertent electrical contact. The connectors consist of a composite material with light weight characteristics and, when used with backshells and contacts specified herein, provide high levels of corrosion resistance and durability. Connectors are designed to be used as a system with backshells and contacts specified herein. When so used, the connectors are capable of performance during or after, as applicable, under the following environmental conditions: −65° to +175°C. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Systems Engineering and Standardization Department (Code 53), Naval Air Engineering Center, Lakehurst, NJ 08733-5100, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. a. Random: 41.7 G RMS at rated high and low temperatures without backshell. 49.5 G RMS at ambient temperature with backshell. b. Sine: 60 G at ambient temperature with backshell. Altitudes from sea level to 100,000 feet (8 torr). Test voltage will vary with altitude (see Table XII). Shock as represented by a 3 + 1 milliseconds base half-sine wave peaking at 300 G (see 3.23). Per MIL-S-901. Humidity conditions up to 98 percent relative humidity including condensation (see 3.25). 2000 hours exposure to salt-laden atmosphere (see 3.15). See 4.6.3. Immersion, in jet fuel, lubrication oil, liquid coolant, hydraulic fluid, gasoline, cleaning compound, defrosting fluid, and solvents (see 3.29). EMI shielding effectiveness: 100 MHZ to 10 GHZ, minimum attenuation of 50 dB (see 3.27). Exposure of uncoupled connector to a salt moisture environment (see 3.34). 1500 matings and unmatings (see 3.4.1, and 3.10). Classification. Connectors fabricated to this specification are scoopproof, self-locking, quick coupling and are as follows: a. Series: The series A and B connectors are not intermateable. A - Utilize MIL-C-38999 insert arrangements. B - Utilize MIL-C-81511 insert arrangements. b. Types: (1) Plugs: Straight. (2) Receptacles: Wall mounting, both front and rear panel mounting, jam nut mounting. Contains grounding member that makes shell contact prior to contact engagement. c. Class: R - Environment resisting - conductive shell. E - Environment resisting. G - Environment resisting - conductive shell, space grade. a. Styles: (1) Connectors ordered with high performance contacts: H - Pin J - Socket The H or J designators are used to indicate a full complement of applicable high performance contacts rated at 1500 cycles of durability, and shall appear in the part number marked on the connector. (2) Connectors ordered with standard contacts: P - Pin S - Socket The P or S designators are used to indicate a full complement of applicable standard contacts rated at 500 cycles of durability, and shall appear in the part number marked on the connector. (3) Connectors ordered without contacts: A - Less pin contacts. Application specifies 500 cycles of durability. B - Less socket contacts. K - Less pin contacts. Application specifies 1500 cycles of durability. L - Less socket contacts. The A, B, K, or L designators are used to indicate connectors ordered less contacts, and are intended to have other than all standard power contacts installed (example: shielded, coaxial and thermocouple contacts). The A, B, K, or L designator shall appear in the part number marked on the connector. Connectors ordered less contacts, but intended for assembly with all high performance or all standard contacts, shall have the H or J designator, or the P or S designator, respectively in the part number marked on the connector the same as connectors ordered with a full complement of applicable contacts. a. Types: (1) Backshells. (2) Protective covers. (3) Dummy stowage receptacles. (4) Sealing plugs. Intended Use: Connectors, contacts and associated hardware are intended for general military use as a system. Used as such, they are particularly suitable for light weight applications and corrosive environments where EMI shielding is required. a. Connectors specified herein are not fully intermountable with those specified in MIL-C-81511 or MIL-C-38999. See detailed specification sheets to determine if these connectors will meet the desired mounting requirements. b. Connectors specified herein are not intermateable with connectors from any other military specification, even though some of the internal components and subassemblies may be used by other connectors. c. Connectors specified herein are not intended for use with accessory hardware configured with interfaces consisting of features constructed from a metal base material. a. Air Force - MIL-C-29600 Series B are not for use. b. Army - MIL-C-29600 Series B are not for use. c. Navy - Connectors specified herein are not for shipboard jacketed cable applications. WARNING: MIL-C-29600 Series A Connectors are not intended for mating with MIL-C-29600 Series B Connectors. Doing so may result in damage to the contacts or the inserts of the connectors. It is specifically critical with shell sizes 10 and 11 when size 20 contacts are used and with shell size 20 and 21 when size 12 contacts are used. These connectors shall not be located next to each other in any application unless the shell keying has been selected to guarantee that the shells will never allow the mating process to begin. However, series A and B connectors are interchangeable. | |
| language | English | |
| title | MIL-C-29600 | num |
| title | CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, COMPOSITE, HIGH DENSITY, QUICK COUPLING, ENVIRONMENT RESISTANT, REMOVABLE CRIMP CONTACTS, ASSOCIATED HARDWARE, GENERAL SPECIFICATION FOR | en |
| type | standard | |
| page | 77 | |
| status | Active | |
| tree | NAVY - AS - Naval Air Systems Command:;1989 | |
| contenttype | fulltext | |
| subject keywords | Accessories | |
| subject keywords | Backshells | |
| subject keywords | Composite | |
| subject keywords | Connectors | |
| subject keywords | Contacts | |
| subject keywords | Pin | |
| subject keywords | Plug | |
| subject keywords | Receptacle | |
| subject keywords | Socket | |
| subject keywords | Threaded coupling |