درباره ما
ASME - ASME International: Recent submissions
Now showing items 241-260 of 1083
-
ASME STP-NU-083
Abstract: Scope: INTRODUCTION Considering the properties of prestressing steel and the level of compression in concrete, prestressed concrete members should respond with lower deflections under blast loading than similarly-sized, ... -
ASME B16.4
Abstract: Scope: This Standard for gray iron threaded fittings, Classes 125 and 250, covers (a) pressure–temperature ratings (b) sizes and method of designating openings of reducing fittings (c) marking (d) material (e) ... -
ASME B107.600
Abstract: Scope: This Standard provides performance and safety requirements for noninsulated, hand-driven screwdrivers and hand-driven, hexagonal shank screwdriver bits intended for manual operation in driving or removing screws. ... -
ASME PTC 34
Abstract: Scope: The rules and instructions given in this Code apply to all waste combustor systems with energy recovery, but the Code cannot detail a test applicable to every variation in the design of waste combustor systems. In ... -
ASME STP-PT-079
Abstract: Scope: INTRODUCTION The objective of this project was to perform thermal analysis of pipeline heating configurations, with the intention of creating guidelines for the sizing of heating bands. The analysis consisted of two ... -
ASME B18.13
Abstract: Scope: This Standard covers general and dimensional data pertinent to the various types of screw and captive washer assemblies, otherwise known as SEMS. SEMS products may include screws, tapping screws, or bolts in sizes ... -
ASME B16.24
Abstract: Scope: Inclusions This Standard covers the following cast copper alloy: (a) threaded pipe flanges and blind flanges having class designations 150, 300, 600, 900, 1500, and 2500 (b) flanged fittings having rating class ... -
ASME A17.1
Abstract: Scope: Equipment Covered by This Code This Code covers the design, construction, operation, inspection, testing, maintenance, alteration, and repair of the following equipment and its associated parts, rooms, spaces, and ... -
ASME PTB-12
Abstract: Scope: PURPOSE AND USE This guideline provides a recommendation and potential guidance to address observed gaps in data and recordkeeping practices that are currently prescribed in the ASME pipeline standards B31.8, B31.8S, ... -
ASME PTC 4.3
Abstract: Scope: This Code applies to all air heaters used in industrial application, e.g., air heaters servicing steam generators and industrial furnaces. This specifically includes (a) combustion gas-to-air heat exchanger including ... -
ASME B31J
Abstract: Scope: General The ASME B31 Code for Pressure Piping and the ASME Boiler and Pressure Vessel Code, Section III, Nuclear Components, Subsections NC and ND piping rules require the use of stress intensification factors (SIFs ... -
ASME BPE
Abstract: Scope: SCOPE OF THE ASME BPE STANDARD The ASME BPE Standard provides requirements for systems and components that are subject to cleaning and sanitization and/or sterilization including systems that are cleaned in place ... -
ASME B16.42
Abstract: Scope: This Standard covers minimum requirements for Classes 150 and 300 cast ductile iron pipe flanges and flanged fittings. The requirements covered are as follows: (a) pressure–temperature ratings (b) sizes and ... -
ASME B18.18
Abstract: Scope: This quality-focused Standard establishes in-process and final inspection requirements for fastener products as well as a receiving inspection plan for fastener purchasers. This Standard identifies four categories, ... -
ASME B30.18
Abstract: Scope: SCOPE EXCLUSIONS Any exclusion of, or limitations applicable to the equipment, requirements, recommendations or operations contained in this Standard are established in the affected volume’s scope PURPOSE The ... -
ASME BTH-1
Abstract: Scope: This Standard provides minimum structural and mechanical design and electrical component selection criteria for ASME B30.20, Below-the-Hook Lifting Devices. The provisions in this Standard apply to the design or ... -
ASME BTH-1
Abstract: This Standard provides minimum structural and mechanical design and electrical component selection criteria for ASME B30.20, Below-the-Hook Lifting Devices.
The provisions in this Standard apply to the design or ... -
ASME PTC 19.14
Abstract: Scope:
THE scope of the work of Committee No. 19 on Instruments and Apparatus is to describe the types of instruments and methods of measurement likely to be required by the ASME ... -
ASME A90.1
Abstract: This Standard applies to the manufacture, installation, maintenance, inspection, and operation of manlifts. Manlifts covered by this scope consist of steps (platforms) and accompanying handholds mounted on, or attached to, ... -
ASME B5.47
Abstract: The standard is confined to milling machine arbors. The reason for confining this standard to this specified milling machine accessory is that through many years of development and general usage, there already exists ...