درباره ما
ASME - ASME International: Recent submissions
Now showing items 421-440 of 1083
-
ASME STP-NU-018
Abstract: EXECUTIVE SUMMARY
This report describes the results of investigation on Task 5 of DOE/ASME Materials Project based on a contract between ASME Standards Technology, LLC (ASME ST-LLC) and Japan Atomic ... -
ASME PTC 19.7
Abstract: OBJECT AND SCOPE
The object of this Supplement is to describe the function, characteristics, advantages, disadvantages, and accuracy of equipment and techniques currently available for the measurement of shaft ... -
ASME B30.22
Abstract: SCOPE OF B30.22
The scope includes only cranes of the types described in para. 22-0.2.1 that are articulated by hydraulic cylinders and powered by internal combustion engines or electric motors and ... -
ASME QAI-1
Abstract: FOREWORD
The 2009 edition of ASME QAI-1 incorporates the 2005 edition of QAI-1, and revisions and additions approved by the QAI Standards Committee since the publication of the 2005 edition. This ... -
ASME B73.1
Abstract: (a) This Standard is a design and specification standard that covers metallic and solid polymer centrifugal pumps of horizontal, end suction single stage, centerline discharge design. This Standard includes ... -
ASME PCC-2S
Abstract: Repair welding considerations in this Article are applicable to pressure vessels for refinery, petrochemical, power generation, and other services where the requirements of this Article apply. Table 1 provides guidance for ... -
ASME PTB-5
Abstract: Example problems illustrating the use of the analysis methods in ASME B&PV Code, Section VIII, Division 3 are provided in this document. -
ASME A17.3 INTERPRETATIONS
Abstract: INTRODUCTION
As a service to persons who use the A17.3 Code for enforcement or as a guide, the A17 Committee renders interpretations of the requirements upon request. The Preface to the Code explains ... -
ASME B16.23
Abstract: This Standard establishes specifications for cast copper alloy solder joint drainage fittings, designed for use in drain, waste, and vent (DWV) systems. These fittings are designed for use with seamless copper tube conforming ... -
ASME B29.26
Abstract: This Standard covers fatigue testing, in axial tension, of power transmission roller chains in ASME B29.1 and ASME B29.100 and nonstandard variants of those chains.
PURPOSE
The purpose of this ... -
ASME B18.6.3
Abstract: This Standard is intended to cover the complete general and dimensional data for the various types of slotted and recessed head machine screws, tapping screws, and metallic drive screws recognized as American National ... -
ASME PTC 7.1
Abstract: OBJECT AND SCOPE
This code provides standard directions for conducting and reporting tests on displacement pumps.
The object of the code is to establish rules for conducting tests on pumps to determine, under ... -
ASME B47.1
Abstract: This Standard covers standard designs for the following:
(a) plain and thread plug gage blanks to 12.010 in. maximum gaging diameter
(b) plain and thread ring gage blanks to 12.260 in. maximum ... -
ASME B18.5.2.2M
Abstract: This Standard covers the complete general and dimensional data for metric series round head square neck bolts recognized as American National Standard, and intended for general applications.
The inclusion of dimensional ... -
ASME B5.1M
Abstract: This Standard applies to T-slots as used on machine tools for the mounting of fixtures, attachments, and accessories; and to the bolts, nuts, and tongues used in such slots. -
ASME B18.2.6 SUPP
Abstract: This Standard covers the complete general and dimensional data for five products in the inch series recognized as an American National Standard. These five structural products include
(a) Heavy Hex Structural ... -
ASME STP-PT-014
Abstract: Composite cylinders have been used for over 50 years in commercial, vehicle, defense and aerospace applications. New materials, processes, design approaches and applications have been incorporated during that time. The ... -
ASME Y14.35
Abstract: This Standard defines the practices for revising drawings and associated documents and establishes methods for identification and recording revisions. The revision practices of this Standard apply to any form of original ... -
ASME RTP-1
Abstract: (a) This Standard applies to stationary vessels used for the storage, accumulation, or processing of corrosive or other substances at pressures not exceeding 15 psig external and/or 15 psig internal above any ... -
ASME B5.47
Abstract: The standard is confined to milling machine arbors. The reason for confining this standard to this specified milling machine accessory is that through many years of development and general usage, there aiready exists good ...