درباره ما
API - American Petroleum Institute: Recent submissions
Now showing items 1061-1080 of 1822
-
API RP 2201
Abstract: Hot tapping is the technique of attaching a welded branch fitting to piping or equipment in service, and then creating an opening in that piping or equipment by drilling or cutting a portion of the piping or equipment ... -
API SPEC 17E
Abstract: This part of ISO 13628 specifies requirements and gives recommendations for the design, material selection, manufacture, design verification, testing, installation and operation of umbilicals and associated ancillary ... -
API STD 527
Abstract: This standard describes methods of determining the seat tightness of metal- and soft-seated pressure relief valves, including those of conventional, bellows, and pilot-operated designs.
The maximum acceptable leakage ... -
API STD 17F
Abstract: This standard is applicable to design, fabrication, testing, installation, and operation of subsea production control systems (SPCSs).
This standard covers surface control system equipment, subsea-installed control ... -
API RP 13J
Abstract: API 13J covers the physical properties, potential contaminants, and test procedures for heavy brine fluids manufactured for use in oil and gas well drilling, completion, fracturing, and workover fluids.
API 13J provides ... -
API SPEC 20E
Abstract: Purpose
This standard specifies requirements for the qualification, production and documentation of alloy and carbon steel bolting used in the petroleum and natural gas industries.
Applic ... -
API STD 607
Abstract: This International Standard specifies fire type-testing requirements and a fire type-test method for confirming the pressure-containing capability of a valve under pressure during and after the fire test. It does not cover ... -
API PUBL 346
Abstract: Scope:
SCOPE AND OBJECTIVES
The project objectives were to:
• identify different technologies available for leak detection and location for the selected ... -
API RP 19G9
Abstract: This document provides recommended practices for the design, operation, optimization, and troubleshooting of dual gas-lift wells.
Compared to single completions, dual completions have a higher initial cost, have more ... -
API PUBL 932-A
Abstract: Scope:
This study was sponsored by the American Petroleum Institute (API), Committee on Refinery Equipment, Subcommittee on Corrosion and Materials Research. The purpose of the ... -
API PUBL 45881
Abstract: FOREWORD
API PUBLICATIONS NECESSARILY ADDRESS PROBLEMS OF A GENERAL NATURE. WITH RESPECT TO PARTICULAR CIRCUMSTANCES, LOCAL, STATE, AND FEDERAL LAWS AND REGULATIONS SHOULD BE REVIEWED.
API IS NOT ... -
API RP T-2
Abstract: INTRODUCTION AND SCOPE
This Recommended Practice provides guidelines for the qualification of personnel engaged in installing, inspecting, testing, and routinely maintaining surface and subsurface ... -
API STD 5T1 ADD 1
Abstract: The purpose of this standard is to provide definitions of imperfections and defects that occur in steel pipe; no criteria as to severity are addressed. The word imperfection as used herein refers to metallurgical and ... -
API 570
Abstract: General Application
Coverage
API 570 covers inspection, rating, repair, and alteration procedures for metallic and fiberglass-reinforced plastic (FRP) piping systems and their ... -
API SPEC 16F
Abstract: PURPOSE
These specifications establish standards of performance and quality for the design, manufacture, and fabrication of marine drilling riser equipment used in conjunction with a subsea Blowout Preventer (BOP) ... -
API PUBL 4452
Abstract: FOREWORD
This, the 1987 Oil Spill Conference, is our tenth biennial meeting. Our efforts to share the knowledge needed to understand the prevention, behavior, control, and cleanup of oil spills now span two ... -
API RP 45
Abstract: This document is directed toward the determination of dissolved and dispersed components in oilfield waters (produced water, injected water, aqueous workover fluids, and stimulation fluids). Bacterial analyses, bioassay ... -
API STD 673
Abstract: This standard covers the minimum requirements for centrifugal fans intended for continuous duty in petroleum, chemical, and gas industry services. Fan pressure rise is limited to differential from a single impeller, usually ...