درباره ما
SAE - SAE International: Recent submissions
Now showing items 921-940 of 16264
-
Inertia Dynamometer Rotor Crack Test Procedure for Air Disc Brakes
Abstract: This Recommended Practice applies to commercial vehicles equipped with air disc brakes and above 4536 kg of Gross Vehicle Weight Rating. Other assessments on the friction material or rotor related to wear, durability, ... -
Performance Requirements for Snap-In Tubeless Tire Valves
Abstract: This SAE Standard for snap-in tubeless tire valves was developed by the qualified engineers in the tire, valve, and automotive industries. It is based upon sound engineering principles, supported by laboratory testing and ... -
Tool and Die Steels
Abstract: This standard covers the identification, classification, and chemical composition of tool and die steels for use by engineers, metallurgists, tool designers, tool room supervisors, heat treaters, and tool makers. -
Abrasive Wear
Abstract: An enormous economic loss, as well as a waste of natural resources, is incurred world-wide as a result of wear of components and tools. Any effort expended in an attempt to reduce this loss is indeed worthwhile. The purpose ... -
Hardness Tests and Hardness Number Conversions
Abstract: This report lists approximate hardness conversion values; test methods for Vickers Hardness, Brinell Hardness, Rockwell Hardness Rockwell Superficial Hardness, Shore Hardness; and information regarding surface preparation, ... -
Electric Motors for Driveline Actuation Standard Terminology, Test Parameters, and Equipment Requirements
Abstract: This document will apply to the most common applications of electric motors, used for activating all-wheel drive (AWD) and four-wheel drive (4WD) disconnect systems as used in passenger (car and light truck) vehicles. The ... -
Motor Vehicle Brake Fluid Container Compatibility
Abstract: Motor vehicle brake fluid must conform to the requirements of SAE J1703 or J1704, not only when manufactured, but also after extended storage in any commercial packaging container. The purpose of this SAE Information Report ... -
Requirements for Engine Cooling System Filling, Deaeration, and Drawdown Tests
Abstract: This SAE Recommended Practice is applicable to all engine cooling systems used in (1) Heavy-duty vehicles, industrial applications, and (2) Automotive applications.There are two categories of coolant reservoir tanks covered ... -
Nomenclature - Clam Bunk Skidder
Abstract: This SAE Recommended Practice identifies major components and parts peculiar to clam bunk skidders. Illustrations used here are not intended to include all existing machines or to be exactly descriptive of any particular ... -
Measurement of Vehicle and Suspension Parameters for Directional Control Studies - Rationale
Abstract: This SAE Information Report presents the background and rationale for SAE J1574-1.The motor vehicle industry is working toward a more complete understanding of the factors affecting the motions of vehicles on the roadway, ... -
Automotive Gray Iron Castings
Abstract: This SAE Standard covers the hardness, tensile strength, and microstructure and special requirements of gray iron sand molded castings used in the automotive and allied industries. Specific requirements are provided for ... -
Measurement of Vehicle and Suspension Parameters for Directional Control Studies
Abstract: The parameters measured according to this SAE Recommended Practice will generally be used in simulating directional control performance in the linear range. (The “linear range” is the steady-state lateral acceleration below ... -
General Information - Chemical Compositions, Mechanical and Physical Properties of SAE Aluminum Casting Alloys
Abstract: The SAE Standards for aluminum casting alloys cover a wide range of castings for general and special use, but do not include all the alloys in commercial use. Over the years, aluminum alloys have been identified by many ... -
Wrought and Cast Copper Alloys
Abstract: For convenience, this SAE Information Report is presented in two parts as shown below. To avoid repetition, however, data applicable to both wrought and cast alloys is included only in Part 1.Part I—Wrought Copper and ... -
Wrought Copper and Copper Alloys
Abstract: This standard1 describes the chemical, mechanical, and dimensional requirements for a wide range of wrought copper and copper alloys used in the automotive and related industries. -
Technical Report on Low Cycle Fatigue Properties Ferrous and Non-Ferrous Materials
Abstract: Information that provides design guidance in avoiding fatigue failures is outlined in this SAE Information Report. Of necessity, this report is brief, but it does provide a basis for approaching complex fatigue problems. ... -
Sintered Powder Metal Parts: Ferrous
Abstract: Powder metal (P/M) parts are manufactured by pressing metal powders to the required shape in a precision die and sintering to produce metallurgical bonds between the particles, thus generating the appropriate mechanical ... -
Magnesium Casting Alloys
Abstract: This document has not changed other than to put it into the new SAE Technical Standards Board FormatThis SAE Standard covers the most commonly used magnesium alloys suitable for casting by the various commercial processes. ... -
Lubricants, Industrial Oils, and Related Products - Classification
Abstract: This index provides an overview of lubricants and symbols for the purpose of assisting the user in the identification of the appropriate product and relevant SAE specification. The aim is to better determine the best ... -
Strain-Life Fatigue Data File Format
Abstract: SAE data file format for exchanging controlled periodic overload data. The object of this SAE Standard is to provide a simple, common methodology for exchanging the data from periodic overload fatigue tests. These tests ...