درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 1361-1380 of 39933
-
Standard Test Method for Float Test for Asphalt Materials
Abstract: 4.1 The float test characterizes the flow behavior or consistency of certain asphalt materials. 4.2 This test method is useful in determining the consistency of asphalt binder or emulsified asphalt residue as one element ... -
Standard Test Method for Burning Quality of Kerosene
Abstract: 5.1 Since the information provided by this test method is largely qualitative in nature, specific limits covering the following characteristics are required in referring to this test method in specifications for kerosene: ... -
Standard Practice for Size Scaling of Tensile Strengths Using Weibull Statistics for Advanced Ceramics
Abstract: 5.1 Advanced ceramics usually display a linear stress-strain behavior to failure. Lack of ductility combined with flaws that have various sizes and orientations typically leads to large scatter in failure strength. Strength ... -
Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester
Abstract: 5.1 The flash point is one measure of the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions. It is only one of a number of properties that should be considered in ... -
Standard Test Methods for Analysis of Lubricating Grease
Abstract: 4.1 These test methods can be used to identify and estimate the amount of some of the constituents of lubricating greases. These test methods are applicable to many, but not all, greases. 4.2 Composition should not be ... -
Standard Test Method for Precipitation Number of Lubricating Oils
Abstract: 4.1 Fully refined petroleum oils normally contain no naphtha-insoluble material. Semirefined or black oils frequently contain some naphtha-insoluble material (sometimes referred to as asphaltenes). This test measures the ... -
Standard Test Method for Softening Point of Pitches (Cube-in-Water Method)
Abstract: 5.1 Pitch does not go through a solid-liquid phase change when heated, and therefore it does not have a true melting point. As the temperature rises, pitch softens and becomes less viscous. The softening point is arbitrarily ... -
Standard Test Method for Relative Density of Solid Pitch and Asphalt (Displacement Method)
Abstract: 5.1 This test method is useful in characterizing pitches and asphalts as one element in establishing uniformity of shipments and sources of supply. -
Standard Specification for Glass Mat Gypsum Panels
Abstract: This specification covers the glass mat gypsum panels. Glass mat interior gypsum panel, designed for use on walls, ceilings, or partitions and that affords a surface suitable to receive decoration. Glass mat coreboard ... -
Standard Test Method for Grout Retention Properties of Ceramic Tile
Abstract: 4.1 This test method provides a means for testing combinations of tile, grout, installation materials and installation practices to determine grout retention behavior. This method can be used by installers to determine if ... -
Standard Practice for Evaluation of Low Angle Light Characteristics
Abstract: 4.1 Some tile surfaces may exhibit variations under low angle conditions as part of the designed aesthetic. 4.2 This practice is intended for tiles that are designed to have an overall uniform appearance under low angle ... -
Standard Test Method for Critical Mode I Interlaminar Strain Energy Release Rate of (G
Ic ) Continuous Fiber-Reinforced Advanced Ceramics at Ambient Temperatures Abstract: 5.1 Interlaminar delamination growth can be a critical failure mode in laminated CMC structures. Knowledge of the resistance to interlaminar delamination growth of a laminated CMC is essential for material development and ... -
Standard Practice for Installation Methods for Adhered Veneer Systems Using Thin Brick Units Made from Clay or Shale
Abstract: 4.1 This practice provides information that, if implemented, will facilitate good installation practices for thin brick in an adhered veneer system. However, this practice cannot address every situation encountered. ... -
Standard Test Method for Determination of Slurry Flow Rate of Fresh Glass Fiber Reinforced Concrete
Abstract: 5.1 Slurry Flow Rates, determined by this test method, are useful for quality control of GFRC products to ensure that manufacturing equipment has been set up to deliver the correct proportions of concrete and glass fiber ...