درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 2501-2520 of 39933
-
Standard Test Method for Evaluation of Carpet Embedded Dirt Removal Effectiveness of Household/Commercial Vacuum Cleaners
Abstract: 4.1 This test method provides an indication of the capability of the vacuum cleaner to remove embedded dirt from carpeting. This test method is based upon results of home cleaning tests so that, in most cases, a reasonable ... -
Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core
Abstract: This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipes made to Schedule 40 iron pipe sizes (IPS) with concentric inner and outer solid ABS layers and a closed-cell ... -
Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
Abstract: 13.1 For the purposes of determining compliance with the specified limits for properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29. -
Standard Specification for Stainless Steel Nuts
Abstract: 15.1 For the purposes of determining compliance with the specified limits for properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29. -
Standard Test Method for Tensile-Tear Strength of Bituminous Roofing Membranes
Abstract: 4.1 Determining the tensile-tear strength of laboratory and field samples of roofing membranes should be useful in developing performance criteria, and as one basis for comparison of different materials and systems. The ... -
Standard Specification and Test Methods for Metallic Bone Staples
Abstract: A1.3 Significance and Use A1.3.1 This test method is used to determine the fatigue resistance of metallic bone staples when subjected to repetitive loading for large numbers of cycles. This information may also be useful ... -
Standard Test Method for Measuring Air Performance Characteristics of Vacuum Cleaners
Abstract: 4.1 The test results allow the comparison of the maximum potential air power available for cleaning tasks when tested under the conditions of this test method. The test results do not indicate the actual air power present ... -
Standard Specification for In-Service Care of Insulating Gloves and Sleeves
Abstract: This specification covers the in-service care, inspection, testing, and use voltage of insulating gloves and sleeves for protection from electrical shock. Gloves and sleeves covered under this specification are designated ... -
Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
Abstract: This specification covers chlorinated poly(vinyl chloride)(CPVC) Schedule 80 pipe fittings intended for use with Iron Pipe Size (IPS) outside-diameter plastic pipe. Materials shall be tested and shall conform to the ... -
Standard Specification for Nonferrous Nuts for General Use
Abstract: 11.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29. -
Standard Test Method for Crimp Frequency of Manufactured Staple Fibers
Abstract: 5.1 This test method for the determination of crimp frequency of manufactured staple fibers may be used for the acceptance testing of commercial shipments but caution is advised since between-laboratory precision is known ... -
Standard Specification for Hardened Steel Washers Inch and Metric Dimensions
Abstract: This specification covers the chemical, mechanical, and dimensional requirements for hardened steel washers for use with fasteners having nominal thread diameters of M12 through M100. These washers are intended for ... -
Standard Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
Abstract: This specification covers material requirements, workmanship, dimensions, and burst pressure for threaded schedule 80 chlorinated poly(vinyl chloride) (CPVC) plastic pipe fittings. Fittings fabricated by backwelding are ... -
Standard Specifications and Test Methods for Metallic Angled Orthopedic Fracture Fixation Devices
Abstract: A2.5 Significance and Use A2.5.1 The test method establishes a uniform cantilever bending fatigue test to characterize and compare the fatigue performance of different angled device designs. This test method may be used ... -
Standard Specification and Test Method for Metallic Bone Plates
Abstract: A2.5 Significance and Use A2.5.1 This test method establishes a uniform four-point bending fatigue test to characterize and compare the fatigue performance of different bone plate designs. This test method may be used to ... -
Standard Safety Specification for Components, Assembly, Use, and Labeling of Consumer Trampolines
Abstract: This safety specification covers the components, the assembly, and the use of consumer trampolines. This specification is intended to reduce the demonstrated hazards associated with the use of trampolines by consumers in ... -
Standard Test Methods for Tension Testing of Nonmetallic Gasket Materials
Abstract: 4.1 These test methods are described in order to standardize procedures for determining the tensile strength of nonmetallic gasket materials. The measurement of this property characterizes various classes and grades of ...