درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 2621-2640 of 39933
-
Standard Test Method for Conducting Rotating Bending Fatigue Tests of Solid Round Fine Wire
Abstract: 5.1 A method for obtaining fatigue strain (stress) at a specific life is of interest to the wire manufacturer, designer and consumer. The method is useful in production control, material acceptance and determination of the ... -
Standard Guide for Recording Occupational Injuries and Illnesses
Abstract: 4.1 This guide is intended to define work-related injuries and illnesses in a way that can be easily understood and measured across countries. These injuries and illnesses can be used to evaluate, compare, and continually ... -
Standard Test Method for Measurement of Initiation Toughness in Surface Cracks Under Tension and Bending
Abstract: 5.1 Surface cracks are among the most common defects found in structural components. An accurate characterization and understanding of crack-front behavior is necessary to ensure successful operation of a structure containing ... -
Standard Guide for Preferred Methods for Acceptance of Product
Abstract: 4.1 Procurement practices encourage industry innovation and provide flexibility to achieve the benefits of continuous improvement. 4.2 There is an evolving industrial product quality philosophy that recognizes the need ... -
Standard Guide for Personal Protective Equipment for the Handling of Flat Glass
Abstract: 4.1 The goal of this guide is to aid in the selection of PPE for the handling of glass that will best protect the affected employee from the remaining hazards identified in the local hazard assessment process. 4.2 This ... -
Standard Specification for Rubber Cellular Cushion Used for Carpet or Rug Underlay
Abstract: 5.1 The purpose of this specification is to provide meaningful tests for rubber cellular cushion used for carpet or rug underlay. -
Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems
Abstract: 5.1 These test methods are intended to evaluate the ability of the HVAC duct system and its supporting construction to do the following: 5.1.1 Resist the effects of a standardized fire exposure, and 5.1.2 Retain its ... -
Standard Practice for Building Enclosure Commissioning
Abstract: 6.1 This practice is intended to serve as a concise, authoritative, and technically sound practice for Building Enclosure Commissioning (BECx) that is based upon: 6.1.1 The Owner Project Requirements; 6.1.2 Clearly defined ... -
Standard Practice for Evaluating Relative Effectiveness of Antimicrobial Handwashing Formulations using the Palmar Surface and Mechanical Hand Sampling
Abstract: 5.1 Hand hygiene is important for preventing the spread of many types of infections. 5.2 During routine activities, it is primarily the palmar surface, comprising palms, fingers, and finger pads, of the hands that may ... -
Standard Practice for Management of Low-Risk Property (LRP)
Abstract: 4.1 LRP should be administratively controlled and managed using less resource-intensive methods than higher-risk property. 4.2 The type and scope of control and management should be commensurate with the level of risk. ... -
Standard Specification for Use of Expanded Shale, Clay, and Slate (ESCS) as a Mineral Component in the Growing Media and the Drainage Layer for Vegetative (Green) Roof Systems
Abstract: This specification covers the quality and grading of expanded shale, clay and slate (ESCS) for use as a mineral component of growing media and drainage layer for extensive and intensive vegetative (green) roof systems. ... -
Standard Guide for Measurement Systems Analysis (MSA)
Abstract: 4.1 Many types of measurements are made routinely in research organizations, business and industry, and government and academic agencies. Typically, data are generated from experimental effort or as observational studies. ... -
Standard Test Methods for Measuring Expansion of Intumescent Materials Used in Firestop and Joint Systems
Abstract: 5.1 These test methods are intended to measure the material’s expansion after heating. 5.2 The test methods also provide a means to determine the expansion factor. -
Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) for X-ray Computed Tomography (CT) Test Methods
Abstract: 5.1 Personnel that are responsible for the creation, transfer, and storage of X-ray tomographic NDE data will use this standard. This practice defines a set of information modules that along with Practice E2339 and the ... -
Standard Practice for Evaluation of Methods for Determination of Kinetic Parameters by Calorimetry and Differential Scanning Calorimetry
Abstract: 5.1 The kinetic parameters provided in this practice may be used to evaluate the performance of a standard, apparatus, technique, or software for the determination parameters (such as Test Methods E698, E1641, E2041, or ... -
Standard Test Methods for Chemical Analysis of Alpha Olefin Sulfonates
Abstract: 33.1 This method is suitable as a quality control test for the measurement of color in alpha olefin sulfonates. -
Standard Terminology for Homeland Security Applications
Abstract: 3.1 In this terminology, definitions used in other ASTM International standards are indicated by following the definition with the designation of the standard. -
Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens
Abstract: 5.1 This practice describes a procedure to gather data intended to measure the uniformity of exposure conditions upon test specimens for the fire test methods described in Test Methods E119, E814, E1529, E1725, E1966, and ...