درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 3101-3120 of 39933
-
Standard Test Methods for Evaluation of Total Sulfation Activity in the Atmosphere by the Lead Dioxide Technique
Abstract: 5.1 Sulfur oxide gases are produced during the combustion of materials containing sulfur. These gases are precursors of atmospheric sulfuric acid, which has been shown to be injurious to living creatures and plants, as ... -
Standard Test Method for Measurement of Asphalt Shingle Mechanical Uplift Resistance
Abstract: 5.1 Uplift resistance is one of the properties of an applied shingle that relates to its ability to withstand wind forces. The mechanical tests described are laboratory methods to measure that resistance at a designated ... -
Standard Test Method for Cold Filter Plugging Point of Diesel and Heating Fuels
Abstract: 5.1 The CFPP of a fuel is suitable for estimating the lowest temperature at which a fuel will give trouble-free flow in certain fuel systems. 5.2 In the case of diesel fuel used in European light duty trucks, the results ... -
Standard Specification for Test Coupons for Steel Castings
Abstract: This specification defines the geometries of several separately-cast and integrally-cast test coupons for use as specified in the applicable casting product or common requirements standard. Procedures for molding, casting, ... -
Standard Test Methods for Single Filament Hose Reinforcing Wire Made from Steel
Abstract: 5.1 The procedures for the determination of properties of single-filament hose reinforcing wire made from steel are considered satisfactory for acceptance testing of commercial shipments of this product because the procedures ... -
Standard Test Method for Determination of Mass Concentration of Particulate Matter from Stationary Sources at Low Concentrations (Manual Gravimetric Method)
Abstract: 5.1 The measurement of particulate matter and collected residue emission rates is an important test method widely used in the practice of air pollution control. Particulate matter measurements after control devices are ... -
Standard Test Method for Mercury Sampling and Analysis in Natural Gas and Other Gaseous Fuels by Amalgamation Atomic Fluorescence Spectroscopy
Abstract: 5.1 This test method can be used to determine the total mercury concentration of natural gas and other sources of gaseous fuels (as defined by Terminology D4150) down to 0.001 μg m-3. It can be used to assess compliance ... -
Standard Guide to International Test Methods Associated with Textile Care Procedures
Abstract: 4.1 This guide identifies U.S., and other international test methods used in the process of determining and evaluating textile and apparel care label instruction effectiveness for properties such as colorfastness, ... -
Standard Test Method for Boiling Range Distribution of Petroleum Distillates in Boiling Range from 174 °C to 700 °C by Gas Chromatography
Abstract: 5.1 The boiling range distribution of medium and heavy petroleum distillate fractions provides an insight into the composition of feed stocks and products related to petroleum refining processes (for example, hydrocracking, ... -
Standard Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and Lubricants
Abstract: 5.1 ASTM test methods are frequently intended for use in the manufacture, selling, and buying of materials in accordance with specifications and therefore should provide such precision that when the test is properly performed ... -
Standard Practice for Calibrating a Fathometer Using a Bar Check Method
Abstract: 4.1 The accuracy of depth measurements made by a fathometer or echo sounder requires a number of corrections because of the variability of sound or acoustic velocity in water with changes in temperature, salinity, and depth ... -
Standard Practice for Treatment and/or Marking of Wood Packaging Materials
Abstract: 4.1 This practice establishes the criteria to treat, or mark, or both WPM with permanent identification for the phytosanitary treatment, or intended service cycle, or both, repair, specification used, and other designated ... -
Standard Guide on the Relationship of Indoor Carbon Dioxide Concentrations to Indoor Air Quality and Ventilation
Abstract: 5.1 Indoor CO2 concentrations have been used as indicators of IAQ for many years, involving both appropriate and inappropriate interpretations of indoor CO2 concentrations (1).5 Appropriate uses include estimating expected ... -
Standard Guide for Painting Inspectors (Concrete and Masonry Substrates)
Abstract: 3.1 This guide is intended as a reference for those responsible for the inspection of thin- or thick-film coating application to concrete and masonry substrates. It does not address the application of cementitious-type ... -
Standard Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks
Abstract: 3.1 It is intended that this practice may be used by manufacturers, users, and testing agencies. The use of this practice establishes a uniform procedure for preparing concrete blocks for the testing of sealants. It is not ... -
Standard Practice for Evaluating Compatibility of Binary Mixtures of Lubricating Greases
Abstract: 5.1 The compatibility of greases can be important for users of grease-lubricated equipment. It is well known that the mixing of two greases can produce a substance markedly inferior to either of its constituent materials. ... -
Standard Specification for Unleaded Aviation Gasoline Containing a Non-hydrocarbon Component
Abstract: This specification covers Grade 82 unleaded aviation gasoline for use only in engines and associated aircraft that are specifically approved by the engine and aircraft manufacturers, and certified by the National Certifying ... -
Standard Test Method for Acetone, p-Chlorobenzotrifluoride, Methyl Acetate or t-Butyl Acetate Content of Solventborne and Waterborne Paints, Coatings, Resins, and Raw Materials by Direct Injection Into a Gas Chromatog
Abstract: 4.1 With the need to calculate volatile organic content (VOC) of paints, and with acetone, p-chlorobenzotrifluoride, methyl acetate and t-butyl acetate considered possible exempt volatile compounds, it is necessary to know ... -
Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility
Abstract: 5.1 The volatile components of a plastisol or organosol influence the weight loss during processing. It is possible that this information will be useful to the producer and user and to environmental interests for estimating ... -
Standard Test Method for Radial Crush Strength of Extruded Catalyst and Catalyst Carrier Particles
Abstract: 5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.