درباره ما
ASTM - ASTM International: Recent submissions
Now showing items 3481-3500 of 39933
-
Standard Test Method for Centrifuge Moisture Equivalent of Soils (Withdrawn 2024)
Abstract: 5.1 All water contained in a saturated soil cannot be removed by gravity drainage alone. The amount of water retained after gravity drainage is usually expressed as the water holding capacity or specific retention of the ... -
Standard Test Methods for Testing Solvent Containing Varnishes Used for Electrical Insulation
Abstract: 4.1 Control—The following tests are useful for control purposes during the manufacture and use of varnishes, and for determining the uniformity of batches: 4.1.1 Specific gravity, 4.1.2 Viscosity, 4.1.3 Flash point, and ... -
Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
Abstract: This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as ... -
Standard Test Method for Saybolt Viscosity
Abstract: 5.1 This test method is useful in characterizing certain petroleum products, as one element in establishing uniformity of shipments and sources of supply. 5.2 See Guide D117 for applicability to mineral oils used as ... -
Standard Practice for Determination of Major and Minor Elements in Aqueous Pore Solutions of Cementitious Pastes by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES)
Abstract: 5.1 The chemical composition of the liquid in cementitious pastes is an important indicator of the solid component reactivity at early times, being influenced by the content and rate of reaction of readily soluble alkali ... -
Standard Specification for Coal Tar Primer Used in Roofing, Dampproofing, and Waterproofing
Abstract: This specification covers coal tar primer suitable for use with coal tar pitch in roofing, dampproofing, and waterproofing below or above ground level, for application to concrete, masonry, and coal tar surfaces. Different ... -
Standard Test Method for Determination of Impact Diameter from Falling Ball on Ceramic Tile
Abstract: 4.1 Impact diameter may be used to interpret impact resistance. 4.2 Maximum impact diameter may be a specified requirement for tile. -
Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
Abstract: This specification covers performance-based manufacture and corresponding test methods for reinforced concrete pipe to be used in the conveyance of sewage, industrial wastes, and storm water, and in the construction of ... -
Standard Guide for Development of Specifications for Fiber Reinforced Silicon Carbide-Silicon Carbide Composite Structures for Nuclear Applications
Abstract: 4.1 Composite materials consist by definition of a reinforcement phase in a matrix phase. In addition, ceramic matrix composites (CMCs) often contain measurable porosity which interacts with the reinforcement and matrix. ... -
Standard Guide for Development of Specifications for Fiber Reinforced Carbon-Carbon Composite Structures for Nuclear Applications
Abstract: 4.1 Composite materials consist by definition of a reinforcement phase in a matrix phase. In addition, carbon-carbon composites often contain measurable porosity which interacts with the reinforcement and matrix. The ... -
Standard Specification for Tool Steel High Speed
Abstract: This specification covers seven tungsten-type (types T1, T2, T4, T5, T6, T8, and T15) and nineteen molybdenum-type high-speed steels (types M1, M2, M3, M4, M6, M7, M10, M30, M33, M34, M36, M41, M42, M43, M44, M46, M47, ... -
Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Commercial/Industrial Building Construction
Abstract: 4.1 In this practice it is recognized that effectiveness, safety, and durability of an RBS depends not only on the quality of the materials, but also on proper installation. 4.2 Improper installation of an RBS will reduce ... -
Standard Practice for Installation and Use of Radiant Barrier Systems (RBS) in Residential Building Construction
Abstract: 4.1 In this practice it is recognized that effectiveness, safety, and durability of an RBS depends not only on the quality of the materials, but also on proper installation. 4.2 Improper installation of an RBS will reduce ... -
Standard Specification for Joints for Concrete Box, Using Rubber Gaskets
Abstract: This specification covers flexible joints for concrete box sections, using rubber gaskets for leak resistant joints. The specification covers the design of joints and the requirements for rubber gaskets to be used. The ... -
Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe, Using Rubber Gaskets
Abstract: This specification covers flexible leak resistant joints for concrete gravity flow sewer pipes using rubber gaskets for sealing the joints, where measurable or defined infiltration or exfiltration is a factor of the design. ... -
Standard Specification for Architectural Flat Glass Clad Polycarbonate
Abstract: This specification covers the quality requirements for cut sizes of architectural flat glass clad polycarbonate (GCP) for use in buildings as security, detention, hurricane/cyclic wind-resistant, and blast and ballistic-resistant ... -
Standard Test Method for Extrusion Rate of Elastomeric Sealants
Abstract: 4.1 Sealants are supplied with various rheological properties ranging from pourable liquids to nonsagging pastes. Single-component sealants are supplied ready for use upon opening the container. Multicomponent sealants are ... -
Standard Test Method for Flow Characteristics of Preformed Tape Sealants
Abstract: 5.1 Tape sealants are tacky, deformable solids, which are used under compression between two or more surfaces of similar or dissimilar substrates in a variety of sealing applications. These tapes are normally supplied in ... -
Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
Abstract: 4.1 Frequently, glass or other glazing or panel materials are structurally adhered with a sealant to a metal framing system. The sealants used for these applications are designed to provide a structural link between the ...