درباره ما
Browsing TIA - Telecommunications Industry Association by Title
Now showing items 1-20 of 1186
-
TIA 252-A
Abstract: INTRODUCTION AND SCOPE
This standard applies to microwave relay communication systems. Usually these systems are multi-hop. They transmit intelligence initially derived from speech, telegraph, data, ... -
TIA 384
Abstract: INTRODUCTION AND SCOPE
The standards contained in this document are intended to be used as performance and interface criteria. As such, these standards may find a typical application in the layout of ... -
TIA EIA-411-A
Abstract: PREFACE
The objectives of EIA-411-A, Electrical and Mechanical Characteristics of Earth Station Antennas for Satellite Communications," are the following:
(a) to provide standard terms, definitions, ... -
TIA EIA-424
Abstract: This Standard details definitions and methods of measurement of characteristics of SSB transmitters and receivers or SSB/AM transmitters and receivers, operating in the SSB mode, intended for operation in the Class "D" ... -
TIA EIA/TIA/IS-63
Abstract: General
This standard specifies a procedure for a modem to automatically detect the modulation technique and data signalling rate of the modem it is connected with. When incorporated into a new modem, ... -
TIA IEB13
Abstract: INTRODUCTION
The purpose of this bulletin is to establish a uniform format for submission of technical data in conjunction with FCC type acceptance of Citizens Band radios.
A type acceptance filing should consist ... -
TIA IS-89
Abstract: These standards detail definitions, methods of measurement, and minimum performance Characteristics of 800 MHz cellular land stations. These standards share the purpose of the Mobile Station - Land Station Compatibility ... -
TIA IS-90
Abstract: These standards detail definitions, methods of measurement, and minimum performance characteristics of 800-MHz cellular subscriber units. These standards share the purpose of the Mobile Station - Land Station Compatibility ... -
TIA J-STD-025-B
Abstract: The scope of this Standard is to define the services to support LAES and the interface between a TSP and an LEA.
Purpose
The purpose of this Standard is to facilitate a TSP's compliance with the ... -
TIA J-STD-025-B-1
Abstract: This addendum only consists of additions to ANSI/J-STD-025-B adding MEID, as follows:
a. Page 12 Line 46: Section 3 -- Definitions and Acronyms – Add Mobile Equipment IDentifier (MEID).
b. Page 92 Line 10: ... -
TIA J-STD-025-B-2
Abstract: This addendum only consists of additions to ANSI/J-STD-025-B adding Carrier Identity information in the cdma2000PacketDataServingSystem message, as follows:
a. Page 72, Line 40: Section 5.5.4 – cdma2000PacketDa ... -
TIA J-STD-025-B-3
Abstract: This addendum consists of additions and modifications to ANSI/J-STD-025-B for supporting BSID or Subnet information in the LocationInformation parameter type of the cdma2000® Abstract Syntax for PacketData ... -
TIA J-STD-026
Abstract: This standard addresses semiconductor chip design. It is intended for applications utilizing standard substrates, materials, assembly, and test methods as well as established semiconductor fabrication and bumping processes. ... -
TIA J-STD-028
Abstract: This standard establishes the construction detail requirements for bumps and other terminal structures on flip chips and chip scale carriers. All flip chip and chip scale device terminals shall meet the designated standards ... -
TIA J-STD-034
Abstract: This document defines the range of application of the current issue of the series. It focuses on overall objectives and basic assumptions. Procedural details are presented in the other recommendations. -
TIA J-STD-036-C
Abstract: This Standard provides a solution for the handling of Wireless Enhanced Emergency Calls for the FCC E911 Phase II mandate.
Carrier position reporting to emergency services systems, as mandated by the Federal Communication ... -
TIA J-STD-036-C-1
Abstract: This Addendum specifies new Class of Service Position Source (CoS) indicators, as well as the associated Position Source codes for the Mobile Positioning Center (MPC) and Positioning Determining Entity (PDE). The new CoS ... -
TIA J-STD-038-B
Abstract: The scope of this standard are the services, information flows and message mappings which require interworking and interoperability functional specifications to support roaming between ANSI-41 MAP and GSM MAP networks. The ... -
TIA J-STD-100
Abstract: This specification is a joint specification between the Alliance for Telecommunications Industry Solutions (ATIS) and the Telecommunications Industry Association (TIA).
One of the objectives of the Commercial Mobile ...