درباره ما
ASME - ASME International: Recent submissions
Now showing items 661-680 of 1083
-
ASME B5.61
Abstract: This Standard applies to hydraulic and mechanical power presses commonly referred to by the metal-working industry as General Purpose, Single Action, Straight Side Type Power Presses that, by means of dies or tooling ... -
ASME PTC 19.3 TW
Abstract: This Standard applies to thermowells machined from bar stock and includes those welded to or threaded into a flange as well as those welded into a process vessel or pipe with or without a weld adaptor.
Thermowells ... -
ASME B18.16.6
Abstract: This Standard covers the complete general, dimensional, mechanical, and performance data for carbon steel, inch series nylon insert locknuts of property grades NE2, NE5, and NE8 designated as American National Standard. ... -
ASME PTC 20.3
Abstract: OBJECT AND SCOPE
The purposes of this Code are:
To establish guiding principles and provide a format for performance specifications for pressure control systems applicable to the equipment covered under ... -
ASME B18.3.4M
Abstract: This Standard contains the complete general and dimensional requirements for Metric Series Hexagon Socket Button Head Cap Screws of nominal sizes from 3 mm to 16 mm recognized as an American National Standard. Also included ... -
ASME B16.36
Abstract: This Standard covers flanges (similar to those covered in ASME B16.5) that have orifice pressure differential connections. Coverage is limited to the following:
(a) welding neck flanges Classes 300, 600, 900, ... -
ASME B31.8S
Abstract: This Code applies to onshore pipeline systems constructed with ferrous materials and that transport gas. The principles and processes embodied in integrity management are applicable to all pipeline systems.
This Code ... -
ASME B18.31.4M
Abstract: INTRODUCTION
This Standard covers the complete general and dimensional data for metric series threaded rod recognized as an American National Standard. This Standard is applicable to both fine and ... -
ASME PTB-1
Abstract: Overview
Part 1, paragraph 1.2 defines the scope of coverage for VIII-2. The term scope refers to both the type of pressure equipment being considered in the development of these rules, as well as the ... -
ASME B1 TECH REPT
Abstract: This Report provides estimates of uncertainty associated with the measurement of pitch diameter, lead and flank angle only for screw thread gages. It is intended that these estimates will be used as a guide to resolve ... -
ASME B40.200
Abstract: This Standard is confined to analog, dial-type bimetallic actuated thermometers utilizing helical bimetallic elements that mechanically sense temperature and indicate it by means of a pointer moving over a scale. -
ASME Y14.2
Abstract: This Standard establishes the line and lettering practices for use in the preparation of drawings, including the recognition of the requirements for computer aided design (CAD) and manually prepared drawings. -
ASME B18.27
Abstract: This Standard covers complete general and dimensional data for three series of general purpose tapered and reduced cross section retaining rings, which may be used with the nominal size shafts and housings listed and ... -
ASME PTC 2
Abstract: This Code contains standards for terms, units of measure, values of constants, symbols, and technical nomenclature that are to be used in all individual test codes. The implication of the words "must," "shall," and "will" ... -
ASME A17.1 HDBK
Abstract: INTRODUCTION
In 1976 I was appointed to the A17 Editorial Committee with Al Land (Chair), William "Bill" Crager (A17 Chair), and Manuel Gutierrez (ASME Secretary). At the time, the A17 Editorial Committee ... -
ASME B18.3.6M
Abstract: This Standard contains complete general and dimensional requirements for metric series socket set screws of nominal sizes from 1.6 mm to 24 mm recognized as American National Standard. Also included are appendices covering ... -
ASME B18.2.3.5M
Abstract: This standard covers the complete general and dimensional data for metric hex bolts recognized as "American National Standard."
The inclusion of dimensional data in this standard is not intended to imply that ...Subject(s) : Bolt , Hex - Metric , -
ASME B18.2.4.3M
Abstract: This standard covers the complete general and dimensional data for metric slotted hex nuts recognized as American National Standard.
The inclusion of dimensional data in this standard is not intended to imply that all ... -
ASME B18.10
Abstract: This Standard covers the complete general and dimensional data for inch series oval neck and elliptic neck track bolts and square nuts intended for use with these bolts, and recognized as an American National Standard. ...