درباره ما
ASME - ASME International: Recent submissions
Now showing items 921-940 of 1083
-
ASME STP-PT-066
Abstract: FOREWORD
This report provides a development of design rules for advanced power plant boilers that pertain to fireside corrosion, erosion and steam oxidation of boiler tubes. These boilers will operate ... -
ASME ASP
Abstract: The scope of this Standard is the standardization of safety and performances requirements for automotive service and maintenance products including, but not limited to
(a) shop presses
(b) oil ... -
ASME A112.18.2
Abstract: This Standard covers plumbing waste fittings of sizes NPS-2 and smaller.
This Standard does not cover
(a) plumbing supply fittings, which are covered by ASME A112.18.1/CSA B125.1;
(b) other devices (e.g., ... -
ASME Y14.1M
Abstract: This Standard defines metric sheet sizes and formats for engineering drawings. Decimal inch sheet sizes and format are defined in ASME Y14.1. For engineering drawing preparation and practices, see ASME Y14.100. ... -
ASME HST-4
Abstract: (a) This Standard establishes performance requirements for electric wire rope hoists for vertical lifting service involving material handling of freely suspended (unguided) loads using wire rope with one of the ... -
ASME B18.6.8
Abstract: This Standard covers the general and dimensional data for the various types of thumb screws and wing screws recognized as standard.
The inclusion of dimensional data in this Standard is not intended to imply that all ... -
ASME B30.20
Abstract: Volume B30.20 includes provisions that apply to the marking, construction, installation, inspection, testing, maintenance, and operation of below-the-hook lifting devices, other than components addressed by other ASME B30 ... -
ASME B107.300
Abstract: This Standard provides performance and safety requirements for manually operated torque instruments, commonly used for mechanical measurement of torque for control of the tightness of threaded fasteners. It is not intended ... -
ASME Y14.34
Abstract: This Standard establishes the minimum requirements for the preparation and revision of application lists, data lists, index lists, parts lists, and wire lists. In addition, this Standard presents certain options that may ... -
ASME PTC 6
Abstract: This Code may be used for testing of steam turbines operating either with a significant amount of superheat in the initial steam (typically fossil-fueled units) or predominantly within the moisture region (typically ... -
ASME B16.25
Abstract: General
This Standard covers the preparation of buttwelding ends of piping components to be joined into a piping system by welding. It includes requirements forwelding bevels, for external and internal ... -
ASME PTC 70
Abstract: This Code provides the procedures, direction, and guidance for the accurate determination, via testing, of the maximum repeatable load change ramp rate, startup load change rate, or shutdown load change rate of a power ... -
ASME PTC 1
Abstract: SCOPE AND ORGANIZATION OF PTCs
Most ASME PTCs are applicable to a specified type of equipment defined by the Code. There may be several subcategories of equipment covered by a single code. Types of ... -
ASME STP-NU-063
Abstract: Purpose
This report presents revised allowable stress values for 304 and 316 stainless steel for inclusion in the ASME Boiler and Pressure Vessel Code (ASME BPV Code), Section III, Subsection NH – ... -
ASME PTB-3
Abstract: Example problems illustrating the use of the design-by-rule and design-by-analysis methods in ASME B&PV Code, Section VIII, Division 2 are provided in this document. Example problems are provided for all calculation ... -
ASME PTC 6A
Abstract: (a) This Appendix has been prepared to facilitate the calculation and correction of turbine test results by furnishing numerical examples of the procedures outlined in The Performance Test Code on Steam Turbines (PTC ... -
ASME B30.21
Abstract: Volume B30.21 includes provisions that apply to the construction, installation, operation, inspection, and maintenance of ratchet and pawl and friction brake type manually lever operated chain, wire rope, and web strap ... -
ASME PTB-6
Abstract: General
The strain gaging of pressure vessels (also known as pressure hulls) subjected to the external hydrostatic test pressure loading serves two purposes. First and foremost, the gaging is to monitor ... -
ASME B16.22
Abstract: This Standard establishes specifications for wrought copper and wrought copper alloy, solder-joint, seamless fittings, designed for use with seamless copper tube conforming to ASTM B88 (water and general plumbing systems), ... -
ASME A112.19.4M
Abstract: This Standard covers materials, methods of inspection, dimensions, testing, and identification of porcelain enameled formed steel plumbing fixtures, such as bathtubs, sinks, and lavatories, which are in general use and demand.