درباره ما
ASME - ASME International: Recent submissions
Now showing items 981-1000 of 1083
-
ASME FFS-1
Abstract: Supplement to In-Service Inspection Codes
The methods and procedures in this Standard are intended to supplement and augment the requirements in API 510, API 570, API 653, and other post construction ... -
ASME OM
Abstract: Section IST establishes the requirements for preservice and inservice testing and examination of certain components to assess their operational readiness in light-water reactor nuclear power plants. It identifies the ... -
ASME B18.21.2M
Abstract: This Standard covers the dimensions, physical properties, and methods of testing for helical spring and tooth lock washers.
The inclusion of dimensional data in this Standard is not intended to imply that all products ... -
ASME Y14.35M
Abstract: This Standard defines the practices for revising drawings and associated documentation and establishes methods for identification and recording revisions. The revision practices of this Standard apply to any form of ... -
ASME STP-PT-049
Abstract: Introduction
The current ASME B31.8 standard ("the Code") requires no derating of line pipe steels for temperatures below 250°F. For pipeline steels in the Grade X60-X70 range, data show ... -
ASME PTC 5
Abstract: The purpose of a test on a reciprocating steam engines is to verify the guarantees given by the manufacturer of the engine or to determine the performance of a given engine with regard to one or more of the following ... -
ASME B1.10M
Abstract: This Standard specifies the thread form, series, tolerance, and designation for the Unified Miniature Screw Threads. The series covers a diameter range of 0.30 mm to 1.40 mm, extending the metric M-Profile and unified ... -
ASME B18.11
Abstract: This standard establishes head types, their dimensions, and lengths of slotted head miniature screws, threaded in conformance with American Standard Unified Miniature Screw Threads, ASA B1.10.
This standard is predicated ... -
ASME A17.3
Abstract: GENERAL
This Code is intended to serve as the basis for state and local jurisdictional authorities in adopting retroactive requirements for existing elevators and escalators to enhance the safety of ... -
ASME B16.10 INTERPRETATIONS
Abstract: Scope:
As a service to persons who use the B16 Standards, the B16 Committee renders interpretations of the requirements upon request. The procedure for requesting an interpretation ... -
ASME NUCLEAR
Abstract: Introduction
The Great East Japan Earthquake and Tsunami inflicted major loss of life and destruction of property on the Nation of Japan, as well as substantial devastation of its environment. Emergency ... -
ASME B29.300
Abstract: Scope:
On August 26, 1998, the B29 Standards committee agreed via letter ballot to consolidate and revise the following three chain standards: ASME B29.6, Steel Detachable Link ... -
ASME MFC-11
Abstract: ASME MFC-11 establishes common terminology and gives guidelines for the selection, installation, calibration, and operation of Coriolis flowmeters for the determination of mass flow, density, volume flow, and other parameters. ... -
ASME NOG-1
Abstract: This Standard covers electric overhead and gantry multiple girder cranes with top running bridge and trolley used at nuclear facilities and components of cranes at nuclear facilities. -
ASME A13.1
Abstract: OBJECT AND SCOPE
This Standard is intended to establish a common system to assist in identification of hazardous materials conveyed in piping systems and their hazards when released in the environment. ... -
ASME PTC 6.2
Abstract: This Code may be used for testing steam turbines in combined cycles with or without supplementary firing and in cogeneration applications. Within these categories of combined and cogeneration cycles, this Code is applicable ... -
ASME B94.21
Abstract: This standard covers types, sizes, tolerances, marking and nomenclature for ground, finishing type gear shaper cutters for generating involute spur and helical gears, splines, and serrations. It also covers ground, ... -
ASME B18.9
Abstract: This Standard covers general and dimensional data for inch series plow bolts recognized as American National Standard.
The inclusion of dimensional data in this Standard is not intended to imply that all of the products ... -
ASME B31.1
Abstract: Rules for this Code Section have been developed considering the needs for applications that include piping typically found in electric power generating stations, in industrial and institutional plants, geothermal heating ...