درباره ما
Standard Specification for Repositionable Pressure-Sensitive Flags
ASTM D6788-24
Organization:
ASTM - ASTM International
Year: 2024
Abstract: This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books, periodicals, and so forth. Flags covered here consist of a single sheet of matte film partially covered by adhesive. A non-adhesive tab or section at one end of the flag serves for easy removal from most surfaces, including paper. The backing shall consist of polyester, polypropylene, or polyethylene film, and shall have a transparent matte surface on one side that is writable by pens and pencils. Flags are available in the following types: Type 1, which are of specified width, and have a colored tab at one end; Type 2, which are of the same width as Type 1, and have a printed message on the top side of the flag; Type 3, which twice the width of Type 1, and have a white tab at one end to highlight writing; Type 4, which are half the width of Type 1, and have a colored tab at one end; and Type 5, which are half the width of Type 1, and have an arrow or a message printed on the top side of the flag. Sampled specimens shall conform to physical requirements in terms of minimum and maximum adhesion, dispension force, and thickness.
Collections
:
-
Statistics
Standard Specification for Repositionable Pressure-Sensitive Flags
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T17:59:30Z | |
| date available | 2025-09-30T17:59:30Z | |
| date copyright | 2024 | |
| date issued | 2024 | |
| identifier other | d6788-24.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/340947 | |
| description abstract | This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books, periodicals, and so forth. Flags covered here consist of a single sheet of matte film partially covered by adhesive. A non-adhesive tab or section at one end of the flag serves for easy removal from most surfaces, including paper. The backing shall consist of polyester, polypropylene, or polyethylene film, and shall have a transparent matte surface on one side that is writable by pens and pencils. Flags are available in the following types: Type 1, which are of specified width, and have a colored tab at one end; Type 2, which are of the same width as Type 1, and have a printed message on the top side of the flag; Type 3, which twice the width of Type 1, and have a white tab at one end to highlight writing; Type 4, which are half the width of Type 1, and have a colored tab at one end; and Type 5, which are half the width of Type 1, and have an arrow or a message printed on the top side of the flag. Sampled specimens shall conform to physical requirements in terms of minimum and maximum adhesion, dispension force, and thickness. | |
| language | English | |
| title | Standard Specification for Repositionable Pressure-Sensitive Flags | en |
| title | ASTM D6788-24 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2024 | |
| contenttype | fulltext | |
| scope | 1.1 This specification covers repositionable pressure-sensitive flags used to mark, flag, and index documents, books, periodicals, and so forth. 1.2 The values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently, without combining values in any way. 1.3 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/D6788-24 |