درباره ما
Standard Practice for Determination of Gas in Coal—Direct Desorption Method
ASTM D7569/D7569M-24
Organization:
ASTM - ASTM International
Year: 2024
Abstract: 5.1 Canister desorption is a widely used technique to measure the gas in coal. The gas level data when normalized to volume/mass and multiplied by coal mass is used to estimate the gas volume in place in an area around the cored well.
Collections
:
-
Statistics
Standard Practice for Determination of Gas in Coal—Direct Desorption Method
Show full item record
| contributor author | ASTM - ASTM International | |
| date accessioned | 2025-09-30T17:59:45Z | |
| date available | 2025-09-30T17:59:45Z | |
| date copyright | 2024 | |
| date issued | 2024 | |
| identifier other | d7569_d7569m-24.pdf | |
| identifier uri | https://yse.yabesh.ir/std/handle/yse/341009 | |
| description abstract | 5.1 Canister desorption is a widely used technique to measure the gas in coal. The gas level data when normalized to volume/mass and multiplied by coal mass is used to estimate the gas volume in place in an area around the cored well. | |
| language | English | |
| title | Standard Practice for Determination of Gas in Coal—Direct Desorption Method | en |
| title | ASTM D7569/D7569M-24 | num |
| type | standard | |
| status | Active | |
| tree | ASTM - ASTM International:;2024 | |
| contenttype | fulltext | |
| scope | 1.1 This practice describes methods for the direct determination of the gas in coal by desorption using samples obtained by drill coring methods from the surface. It sets out guidelines for the equipment construction, sample preparation and testing procedure, and method of calculation. 1.2 Indirect methods for the determination of the gas in coal (not covered in this practice) are based on either the gas absorption characteristics of coal under a given pressure and temperature condition or other empirical data that relate the gas in coal to such other parameters as coal rank, depth of cover, or gas emission rate. 1.3 This practice covers the following two direct methods, which vary only in the time allowed for the gas to desorb from the core, or sidewall core, before final crushing: 1.3.1 The slow desorption method in which volumetric readings of gas volume are taken frequently (for example, every 10 min to 15 min) during the first few hours, followed by hourly measurements for several hours, and then measurements on 24-h intervals until no or very little gas is being desorbed for an extended period of time. 1.3.2 The fast desorption method in which after initial desorbed gas measurements to obtain data for lost gas calculations are taken, the canister is opened and the sample is transferred to the coal crusher. The remaining gas volume is measured on a crushed sample. 1.4 This practice is confined to the direct method using core, or sidewall core obtained from drilling. The practice can be applied to drill cuttings samples; however, the use of cuttings is not recommended because the results may be misleading and are difficult to compare to the results obtained from core desorption. The interpretation of the results does not fall within the scope of the practice. 1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. | |
| identifier DOI | 10.1520/D7569_D7569M-24 |